background image

WM110S-120S-130S

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.

 IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components attached to the short throw projector mounts
up to (and including) the projector does not exceed 50 lbs
(22.68 kg) for the WM110 or the WM120; or 25 lbs (11.34 kg)
for the WM130.

DIMENSIONS

7.55

110S, TRAVEL 11.25" - 18"

130S, TRAVEL 28" - 52.5"

120S, TRAVEL 16" - 28.5"

110S, 14.49" MIN - 21.71" MAX

130S, 32.78" MIN - 58.21" MAX

120S, 20.74" MIN - 34.21" MAX

LEVELING ADJUSTMENT

3

 OF

10.38

8.38

.50

.328 TYP

2.50

6.38

14.13

13.00

6.02

7.40

2.52

5.31

1.42

1.09

CABLE CHANNEL

DIMENSIONS THRU ARM

DIMENSIONS:  INCHES

Summary of Contents for WM-110

















Reviews: