background image

Installation Instructions

 MSP-WM46UN2X2

5

ASSEMBLY AND INSTALLATION

Mount Assembly

1.

Arrange four vertical brackets (B-D) with two horizontal 
brackets (A) making sure the right vertical bracket (C) is on 
the far right and the left vertical bracket (D) is on the far left. 
(See Figure 1)

2.

Use 16 5/16-18" lock nuts (L) to attach vertical brackets to 
horizontal brackets. (See Figure 1)

Figure 1

Attach Mount to Wall - Concrete

NOTE:  

If attaching to wood studs, proceed to Attach Mount to 

Wall - Wood Studs section.

1.

Determine mounting location on wall.

2.

Determine mounting slots to be used for installation. (See 
Note below and Figure 2)

NOTE:  

Slots used must be at least 24" apart. Mount must be 

centered on a/- 4 1/2". (See Figure 2)

Figure 2

3.

Using assembled mount as a template, mark four holes in 
selected mounting holes on wall. Use a level to make sure 
of an even mount. (See Figure 3)

4.

Drill four 3/8" holes in wall 2 1/2" deep at marked locations. 
(See Figure 3)

5.

Install four concrete anchors (M) into four drilled holes on 
wall. (See Figure 3)

6.

Install four 3/8 x 2 1/2" hex head lag screws (N) through 
holes on mount and into four concrete anchors. (See Figure 
3)

Figure 3

(B) x 2

(L) x 16

2

(C)

(D)

(A) x 2

24" min. centered

24" min.(4 1/2" right)

24" min.(4 1/2" left)

(M) x 4

5

6

(N) x 4

3

4

x 4

Summary of Contents for MSP-WM46UN2X2













Reviews: