10
13
conditions of use as provided for by the instructions for use.
The warranty shall not therefore apply in the case of damages
caused by improper use, wear or accidental events.
For the duration of warranty on conformity defects please refer to
the specific provisions of national laws applicable in the country of
purchase, where provided.
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition after
each wash.
HOW TO OPEN THE COT
1. Remove the frame (A) from the bag (D).
2. Insert the legs (B) in the supports of the frame until an engage-
ment click is heard (Fig. 1).
3. After releasing the buckle (F), Fig. 2, open the frame (A) in the
direction of the arrows (Fig. 3). A double CLICK indicates that the
structure was opened and locked correctly.
4. The straps and closing buckles can be put back in the pockets
located below the base of the cot (Fig. 4).
HEIGHT ADJUSTMENT OF THE BASE
The height of the base of the cot can be adjusted to two positions:
lifted (0-6 months), Fig. 5, and completely lowered (0-24 months),
(Fig. 6).
WARNING: When in its highest position the cot is intended for use by
children between the ages of 0 and 6 months (weighing up to 9 kg).
WARNING: When a child is able to sit, kneel or to pull themselves
up, the cot should no longer be used with the base in the higher
position; this should now be completely lowered.
5. To adjust the height of the base of the cot, use the zipper (C) lo-
cated on the outside of the cot (Fig. 7 - 8 - 9). Open the zip com-
pletely to lower the base of the cot (Fig. 6). To use the cot with
the base completely lowered, the velcro straps located on the
mattress must be inserted and secured in the slots at the bottom
of the cot (Fig. 10-11-12).
By removing the mattress velcro straps from the base of the cot the
base of the cot will return to the raised position (Fig. 5).
HOW TO CLOSE THE COT
6. Press the two buttons located in the centre on the top of the long
side of the cot (Fig. 13) and fold the cot in the direction of the arrows
(Fig. 14).
7. Insert all the components inside the bag (D) for easy transport
(Fig. 15).
REMOVING THE COVER
8. Remove the mattress being careful to unfasten the velcro straps
as indicated in the“HEIGHT ADJUSTMENT OF THE BASE”paragraph.
9. To remove the cover from the mattress, use the six zippers lo-
cated on the top edges of the cot (Fig. 16) and pull the plastic
elements off the corners, carefully removing the fabric from the
frame (Fig. 17).
10. Remove the central wooden slat from the pocket on the base
of the cot (Fig. 18).
11. To remove the cover from the mattress open the cover, fastened
with velcro straps inside it (Fig. 19), delicately remove the wood-
en base and padding.
12. To re-cover the product, follow these steps in reverse order.
ACTIVATING/DEACTIVATING SWING MODE
WARNING: This function may be used ONLY when the base of the
cot is in the lifted position (0 - 6 months).
13. To activate this function, push the 4 buttons (G) down individual-
ly with one hand and lift each foot with the other hand (Fig. 20).
14. To deactivate the swing function, push the 4 buttons (G) down
individually and lower the 4 feet (Fig. 21).
WARRANTY
The product is guaranteed against any conformity defect in normal
Summary of Contents for ZIP & GO
