Chicco OASYS 2/3 FixPlus, Instructions For Use Manual

Page: 21 / 24

20
Installing the child seat inside the
vehicle without the child inside
When the child is not travelling in the car,
the child car seat should be left secured
by the vehicle three-point safety belt, or
stowed away in the car boot. An unsecured
child car seat may be a source of danger
for the other passengers in the event of an
accident or sudden braking.
How to remove the child from the child
car seat
Release the car belt buckle, accompanying
the belt as it retracts.
Removal of the child car seat
WARNING! Remove the child from the
child car seat before removing it.
1. Release the car safety belt.
2. Unthread the diagonal strap through the
guide, accompanying it as it retracts.
If the rigid clasps have been used to fasten
the car seat in place, they must now be
released from the anchor points:
1. Pull the two red buttons on the rigid
clasp release system towards you, release
the clasps from the corresponding Isofix
anchor points on the car seat (Diag. 18) so
that the indicator is completely red.
2. Hold the lever up (O) as you push the
rigid clasps all the way into the base of the
child car
seat, (Diag. 19).
Installing and removing the cup
holder
The child car seat has 2 inserts, one on
the right and one on the left of the side of
the seat where you can fit the cup holder
whenever you like.
To install the cup holder:
1. Insert the cup holder into the relative
guide (Diag. 20)
2. Press the cup holder downwards until it
clicks into place (Diag. 21).
WARNING! Do not place glass containers or
21
1. Rotating it counter clockwise will
increase the width of the backrest (Diag.
26) while rotating it clockwise will decrease
the width (Diag. 27).
Adjusting the inclination of the child
car seat backrest/seat
It is possible to recline the child car seat by
using the reclining adjuster button (H).
The child car seat backrest/seat can be
reclined to 4 different positions to allow
the child to travel in
absolute comfort. To recline the backrest
simply grasp hold of the front section of
the seat (Diag. 28) and pull it towards you.
Simply press the reclining adjuster button
(H) pushing the seat backwards towards
the vehicle seat backrest to return it to a
vertical position.
WARNING! never recline the child car seat
when in use. Before adjusting the backrest,
remove the child from the child car seat.
After reclining or straightening the Oasys
child car seat, always check that the car
3-point safety belt is sufficiently taut and
a maximum of 2 cm above the shoulder
of the child (Diag. 23). Always perform the
above operations when the vehicle is at a
standstill.
Removable backrest/seat covers
The child car seat fabric cover is completely
removable and washable. It is attached
to the structure using velcro straps and
elastics (Diag. 29)
Straighten the backrest (C) upright and
widen the side flaps (N).
Backrest
Start from the lower section of the side
flaps, separate the fabric lining from
the Velcro fasteners (diag. 30) and lift it
off. Now separate the central section of
the backrest working from the bottom
upwards, removing the entire cover,
including the headrest section, undoing
hot liquids on the cup holder as they could
harm the child.
To remove it:
1. Press the lever on the back of the cup
holder and lift it upwards, out of the guide
(Diag. 22)
The cup holder guides are fitted with a
special device that makes sure it always
remains in a horizontal position.
To rotate and position the cup holder:
1. Press the lever on the back and rotate it
to the desired position
Adjusting the height of the back rest
The height of the headrest can be adjusted
to 10 different positions to adapt the child
car seat to
the height of the child.
Make sure the child’s head is always well
protected and the car diagonal safety belt
is positioned
properly on his shoulder.
When adjusting the height of the backrest,
check that the diagonal belt loop (B) is
positioned at
a maximum of 2 cm above the child’s
shoulder (Diag. 23)
To make the adjustment:
1. Use one hand to press the child car seat
backrest height adjuster lever (L) located
on the back of the headrest (Diag. 24)
2. Raise/lower the backrest to adapt it to
the height of the child’s shoulders (Diag.
25)
3. Release the lever checking that it has
clicked into the desired position.
Adjusting the width of the back rest
The width of the backrest can be adjusted
to adapt the child car seat to suit the
physique of
the child. Use the backrest width regulator
wheel (K) located above the headrest, to
adjust the width: