manualshive.com logo in svg

Chicago Pneumatic CPG 90-120 JD, Instruction Manual

Share
Download
Chicago Pneumatic CPG 90-120 JD Instruction Manual Download Page 17

- 17 -

Battery Voltage display

This view shows the Battery voltage and the running
hours.

Coolant temperature display

This view shows the Coolant temperature and the
running hours.

See also “Parameter list” on page 18 for selection
between °C and °F.

Oil pressure display

This view shows the Oil pressure and the running
hours.

See also “Parameter list” on page 18 for selection
between bar and psi.

Fuel level display

This view shows the Fuel level and the running hours.

Voltage - frequency - running hours 
display

This view shows the voltage, frequency and running
hours.

Engine speed display

This view shows the engine speed and running hours.

Qc1002™ Menu Description

Status Display (pop-up window)

In case special statuses are entered, a pop-up window
will automatically be entered for as long as the status
is active.

The background screen is not updated when the status
pop-up window is active.

These special statuses are:

13.2 V

Battery

00168.1h

144˚F

Water

00168.1h

58psi

Oil

00168.1h

75%

Fuel

00168.1h

60Hz

480V

00168.1h

1800

RPM

00168.1h

PREHEAT

START OFF/
EXTENDED 
STOP TIMER

COOLDOWN

Summary of Contents for CPG 90-120 JD

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands