manualshive.com logo in svg

Chicago Faucets Geberit Tessera, Installation Instructions Manual

Share
Download
Chicago Faucets Geberit Tessera Installation Instructions Manual Download Page 7

7

Geberit Tessera

TM

Toilet System

Installation & Maintenance Instructions

WALL HUNG BOWL INSTALLATION

5

6

7

8

1. Remove clear plastic sleeves fom threaded 

rods.

2. Adjust rods to protrude 3” from finished wall

surface.

3. Secure rods to carrier frame using hex nuts 

(provided).

1. Lubricate rubber seals with lubricant

provided.

Do not use plumbers putty or Silicone
sealant.

2. Install both adapters into appropriate wall 

side hub.

1. Place the bowl onto the fixture rods.

2. Install cap retainers (1), washers (2) and

nuts (3). Secure bowl with nuts, handtight
only.

Note: Cap retainers (1) should be installed with
the larger end facing up.

3. Level the bowl, then tighten nuts.

DO NOT OVERTHIGTEN NUTS.

4. Snap caps over cap retainers (4).

3"

1"

up

1

2

3

4

9

Note: 
Sound barrier pad
optional, separate
order required.

Caulk gap around
bowl with water-
proof sealant.

Summary of Contents for Geberit Tessera











Reviews:

No comments

Brands by name

Popular brands

Load more brands