background image

SKU 99823 

For technical questions, please call 1-800-444-3353. 

Page 12

liMited 90 day Warranty

Harbor Freight Tools Co. makes every 

effort to assure that its products meet 

high quality and durability standards, and 

warrants to the original purchaser that this 

product is free from defects in materials 

and workmanship for the period of 90 days 

from the date of purchase. This warranty 

does not apply to damage due directly or 

indirectly, to misuse, abuse, negligence or 

accidents, repairs or alterations outside 

our facilities, criminal activity, improper 

installation, normal wear and tear, or to 

lack of maintenance. We shall in no event 

be liable for death, injuries to persons 

or property, or for incidental, contingent, 

special or consequential damages arising 

from the use of our product. Some states 

do not allow the exclusion or limitation 

of incidental or consequential damages, 

so the above limitation of exclusion may 

not apply to you. THIS WARRANTY IS 

ExPRESSLY IN LIEU OF ALL OTHER 

WARRANTIES, ExPRESS OR IMPLIED, 

INCLUDING THE WARRANTIES OF 

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, 

the product or part must be returned to 

us with transportation charges prepaid. 

Proof of purchase date and an explanation 

of the complaint must accompany the 

merchandise. If our inspection verifies 

the defect, we will either repair or replace 

the product at our election or we may 

elect to refund the purchase price if 

we cannot readily and quickly provide 

you with a replacement. We will return 

repaired products at our expense, but if we 

determine there is no defect, or that the 

defect resulted from causes not within the 

scope of our warranty, then you must bear 

the cost of returning the product.

This warranty gives you specific legal 

rights and you may also have other rights 

which vary from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009    

Camarillo, CA 93011  •  (800) 444-3353

Summary of Contents for 99823













Reviews: