manualshive.com logo in svg

Chevrolet 2004 Impala, Owner'S Manual, Page: 95 / 410

Share
Download
Chevrolet 2004 Impala Owner'S Manual Download Page 95

Parking Brake

The parking brake is
located to the left of the
brake pedal, near the
driver’s door.

To set the parking brake, hold the brake pedal down
with your right foot. Push down the parking brake pedal
with your left foot.

To release the parking brake, hold the brake pedal
down with your right foot and push the parking brake
pedal with your left foot. When you lift your left foot, the
parking brake pedal will follow it to the released
position.

A warning chime will sound if the parking brake is set,
the ignition is on and the shift lever is not in PARK (P).

Notice: Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Verify that
the parking brake is fully released and the brake
warning light is off before driving.

If you are towing a trailer and parking on any hill, see
Towing a Trailer on page 4-38. That section shows what
to do first to keep the trailer from moving.

Shifting Into Park (P)

{

CAUTION:

It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.

Do not leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle will not move, even when you are on
fairly level ground, always set your parking
brake and move the shift lever to PARK (P). See
Shifting Into Park (P) on page 2-27. If you are
pulling a trailer, see Towing a Trailer on
page 4-38.

2-27

Summary of Contents for 2004 Impala



























































































































































































































































































































































































































Reviews:

No comments