manualshive.com logo in svg

Chevrolet 2004 Impala, Owner'S Manual, Page: 228 / 410

Share
Download
Chevrolet 2004 Impala Owner'S Manual Download Page 228

To turn the system on or
off, press the TRAC OFF
button on the left side
of the instrument panel.

When you turn the system off, a chime will sound and the
TRAC OFF warning light will come on and stay on. If the
traction control system is limiting wheel spin when you
press the button to turn the system off, the warning light
will come on and the system will turn off right away.

You can turn the system back on at any time by
pressing the button again. The TRAC OFF warning light
should go off.

Steering

Power Steering

If you lose power steering assist because the engine
stops or the system is not functioning, you can steer but
it will take much more effort.

Steering Tips

Driving on Curves

It is important to take curves at a reasonable speed.

A lot of the “driver lost control” accidents mentioned on
the news happen on curves.

Here is why:

Experienced driver or beginner, each of us is subject to
the same laws of physics when driving on curves.
The traction of the tires against the road surface makes
it possible for the vehicle to change its path when
you turn the front wheels. If there is no traction, inertia
will keep the vehicle going in the same direction. If
you have ever tried to steer a vehicle on wet ice, you
will understand this.

The traction you can get in a curve depends on the
condition of your tires and the road surface, the angle at
which the curve is banked, and your speed. While
you are in a curve, speed is the one factor you
can control.

4-10

Summary of Contents for 2004 Impala



























































































































































































































































































































































































































Reviews:

No comments