background image

Top Newel Cap or
Handrail Landing Connector

If your balustrade ends at the top of the stairs, then you 
can finish off the newel with our Newel Cap (AXEVNC).  
However  if  you  have  balustrade  coming  off  the  top 
newel, typically at a 90

o

 angle (for return landings please 

see instructions below), then you can use our Landing 
Handrail Connector (AXEVLHC).

To  install  the  Landing  Handrail  Connector  simply  slide 
it  onto  the  top  newel  and  secure  using  the  30mm 
screw  provided,  making  sure  you  have  lined  it  up  with 
your landing baserail.  It is now ready for you to insert 
the  handrail  and  secure  using  the  two  30mm  screws 
provided (fig. 11).

The handrail can terminate to either a wall connector, or 
to another newel to handrail connector where there is a 
second flight of stairs.

Intermediate Newel on the Rake

If your staircase is longer than 3.9m (measured between 
inside newel faces) then you will require an intermediate 
newel for added strength.

This will require an additional newel base to be installed 
at the same time as the top and bottom bases, the cut 
off point for the intermediate newel base is 150mm.  The 
intermediate newel post must be cut to 590mm before 
fitting the collar and inserting it into the base.

Next  fit  the  intermediate  connector  (AXEVIC)  onto  the 
top of the newel and secure with the two 30mm screws 
provided.  Then slide the other half of the intermediate 
connector  onto  and  up  the  handrail,  once  located  into 
the newel connector, secure to the handrail by using the 
four 30mm screws provided.

Finally  secure  the  connector  assembly  by  inserting 
the  45mm  bolt  and  spacer  provided,  making  sure  the 
chamfered  end  goes  into  the  hole  first.  Finish  off  by 
inserting the cover cap into the bolt hole (fig. 12).

axxys

®

 evolution 

fitting instructions

www.axxys.co.uk

Summary of Contents for axxys evolution













Reviews: