manualshive.com logo in svg

Chery Tiggo 5 T21, Manual

Share
Download
Chery Tiggo 5 T21 Manual Download Page 74

Training Center of After-Sales Department Chery International

4. BCM 

74

3. Function description

18 

Lock/unlock 

by central 

control 

1.  Lock/unlock by remote controller
If:

①

The key is turned to OFF 

②

Four doors are closed 

③

BCM  receives 

lock signal from remote controller, all doors will be locked, left/right turning 
lamps will flash once and the horn will beep once shortly. 
If: 

①

Any door is not closed properly 

②

The key is  turned to OFF 

③

BCM  

receives lock signal from remote controller,  all doors will lock one time 
and unlock one time with turning lamps flashing twice. 
If: 

①

Four doors are closed properly 

②

The engine hood or trunk lid is not 

closed properly 

③

The key is  turned to OFF 

④

BCM  receives lock signal 

from remote controller, once BCM receives unlock signal from remote 
controller, the central control will unlock once with left/right turn signal 
lamps flashing twice. 
2. Lock/unlock by central control 
If four doors are closed, press lock switch, the doors will be locked.  
Press unlock switch of central control, the doors will be unlocked. 
If any door is not closed properly, press lock switch, the doors will not be 
unlocked.

MASHINESOFT.COM

09120146259

Summary of Contents for Tiggo 5 T21






























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands