background image

Appendix A: Regulatory and Safety

Page A-3

Important Information to our Users in Europe

CE Regulatory Compliance Statement

Where applicable, Checkpoint Systems, Inc. offers certain Electronic Article Surveillance (EAS) 
products that have CE Declarations of Conformity according to R&TTE Directive 99/5/EC, EMC 
Directive 2004/108/EC, and Low Voltage Directive 2006/95/EC.

System Electromagnetic Compatibility (EMC) has been tested and notified through Spectrum 
Management Authorities if necessary, using accredited laboratories, whereby, conformity is declared 
by voluntarily accepted European Telecommunications Standards Institute (ETSI) standards EN 
301489-3 and EN 302208 and/or EN 300330, as applicable.

NOTE: Certain Electronic Article Surveillance (EAS) equipment have been tested and found to 
conform to the CE emission and immunity requirement in Europe. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio communications. Under 
unusual circumstances, interference from external sources may degrade the system 
performance, which may include intermittent decreases in detection and/or intermittent 
increases in alarm activity. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment experiences frequent interference from external sources 
or does cause harmful interference to radio communications reception, which can be 
determined by turning the equipment off and on, please contact a Checkpoint Systems 
representative for further assistance.

RoHS Compliance Statement

The RoHS Directive stands for "the restriction of the use of certain hazardous substances in electrical 
and electronic equipment." A RoHS compliant product means that electrical and electronic equipment 
cannot contain more than maximum permitted levels of lead, cadmium, mercury, hexavalent 
chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE). Checkpoint is 
in compliance with the RoHS directive.

WEEE Compliance Statement

The Waste Electrical and Electronic Equipment Directive (WEEE) applies to companies that 
manufacture, sell, distribute, or treat electrical and electronic equipment in the European Union. There 
are a number of obligations imposed on Checkpoint as a supplier of electrical and electronic 
equipment. Checkpoint's compliance approach for each of these obligations is provided below.

Summary of Contents for Counterpoint iD














Reviews: