manualshive.com logo in svg

Checkline TI-007X, Operating Manual, Page: 6 / 40

Share
Download
Checkline TI-007X Operating Manual Download Page 6

– 5 –

2.4   GAIN Key   

The TI-007X has an adjustable gain feature for additional versatility to control 
the overall output of the gauge, to compensate for various materials and 
applications. There are five gain settings (VLOW, LOW, MED, HIGH, VHI) 
when pulse-echo or thin PLAS mode is selected, and three gain settings (LOW, 
MED, HIGH) for all other modes where automatic gain control is used. Refer to 
8.1 for details regarding the gain feature..

2.5   SCAN Key  

Th  offers a high speed scan feature. This feature allows for scanning larger areas 
on a given test material, while still offering reasonable representation of 
thickness.

2.6   +/- Increment/Decrement Key’s 

  

The +/- Keys are used to increment/decrement values,  
navigate menus, and select menu options. 

2.7   MODE Key   

The MODE key toggles the measurement modes. If a delay line transducer (dLY) 
is selected from the PROB menu option, echo-echo (E-E) and interface-echo (I-E) 

modes will be toggled. If a contact transducer (Con) is selected, pulse-echo (P-E) and 
echo-echo (E-E) modes will be toggled. Finally, if the plastic transducer (PLAS) option 
is selected, the thickness options thin (thin) and thick (thK) will be toggled. The 
measurement modes and transducer styles offer the flexibility to address specific 
application scenarios. Refer to section 7.0 for an explanation on the various calibration 
options. 

2.8   MENU Key  

The MENU key is used to access and set all of the additional features of the 
TI-007X that are not at the top level of the keypad with a dedicated key. The 
features and setting are outlined in the table below:

Summary of Contents for TI-007X









































Reviews:

No comments