manualshive.com logo in svg

Checkline TI-007X, Operating Manual, Page: 34 / 40

Share
Download
Checkline TI-007X Operating Manual Download Page 34

–33 –

9.0 CONNECTIVITY AND POWER

9.1   Connectivity

The TI-007X is equipped with a USB-C connector and offers serial over USB using a 
CDC (Communications Data Class) and software wedge to transfer data into common 
text editors and spreadsheet software programs as needed. The TI-007X does not have 
any internal memory to store data, but is used to connect to external storage devices 
such as SPC data collectors and PC based software programs. We also offer a standard 
serial hardware option, as well as a wireless Bluetooth module that can be installed 
on the PC board of the TI-007X. Refer to our price list for additional information on 
communication module options and cables.

9.2   Installing Serial Driver

When the TI-007X is powered on and connected to the PC, and no CDC driver was 
previously installed, the following message will be displayed: 

The driver file that needs to be installed can be found by installing our DakView PC 
software, and located in the USB directory. The file name is CDC_Ultrasonics.inf, and 
can be downloaded and saved anywhere on your local PC. 

To install the driver, open Control Panel, followed by selecting Device Manager:   Right 
click on the CDC device as illustrated above, and select “update driver”. The following 
window will appear: 

Summary of Contents for TI-007X









































Reviews:

No comments