manualshive.com logo in svg

Checkline TI-007X, Operating Manual, Page: 33 / 40

Share
Download
Checkline TI-007X Operating Manual Download Page 33

–32 –

5.  When the desired VX setting is displayed, press the

key to set the status  

 

and return to the measurement screen.

8.10  Lock

The lock feature was built into the TI-007X for the purpose of locking the operators 
out of editing any of the gauge settings, for purposes of consistency between operators. 
When the lock feature is enabled, the gauge calibration functionality cannot be altered, 
as well as any of the individual features in the gauge. The only keys that are always 
unlocked are the power and probe zero keys, as these must remain unlocked for 
measurement functionality.

The procedure to enable/disable the lock feature is outlined below:

1.  With the TI-007X powered off, press and hold down the

key while  

 

powering the TI-007X on . The lock icon will 

be  

 

illuminated on the display.

2.  To unlock the TI-007X repeat step one, but hold down the

key while  

 

 

powering the  TI-007X on.

8.12  Factory Defaults

The TI-007X can be reset to factory defaults at any time to restore the original gauge 
settings. This should only be used if the gauge is not functioning properly, or perhaps 
multiple features have been enabled and a clean start is needed.

The procedure to reset the gauge is outlined below: 

1.  With the TI-007X powered off, press and hold down the 

and

keys  

 

while powering the TI-007X on .

NOTE: 

Once the measurement screen is displayed the keys can be released. 

Summary of Contents for TI-007X









































Reviews:

No comments