82
3 ALLGEMEINE ANWENDUNG
Die Messungen werden entweder direkt (Spannungs-, Frequenz- und Strommessung bei
angeschlossener Messzange) oder durch Betätigung der TEST Taste durchgeführt.
Die Spannungs- und/oder Frequenzmessungen sind über alle „aktiven“ Positionen des Wahlschalters
zugänglich.
3.1 AUTOMATISCHE PRÜFUNGEN
3.1.1 PRÜFUNG DER PHASENLAGE (NETZSTECKDOSE)
Wenn das Messgerät angeschlossen wird, misst es die Spannung zwischen den Leitern „L“ und „N“
(U
LN
), zwischen den Leitern „L“ und „PE“ (U
LPE
), zwischen den Leitern „N“ und „PE“ (U
NPE
) sowie
zwischen der Spannungssonde – wenn ein Staberder an die Buchse (P) angeschlossen ist – und dem
Leiter „PE“.
Der die höchste Spannung aufweisende Leiter wird als Phase „L“ bezeichnet und durch eines der
folgenden Zeichen gekennzeichnet:
oder
Die mit dem Gerät gelieferte Leitung trägt ein weißes Kennzeichen, um Phasenlage an der
Netzsteckdose zu bestimmen.
Ferner bestimmt das Gerät für alle Werte
≥
15,3 Hz die Frequenz und den Gehalt.
3.1.2 PRÜFUNG DES SCHUTZLEITERS (PE)
Wenn man bei der Schleifenimpedanzmessung (ZLOOP) oder bei der Erdungsprüfung unter
Spannung (REARTH) die TEST Taste betätigt, misst das Gerät zuerst den Potentialunterschied U
C
zwischen der lokalen Erde (Spannung des Bedieners über die TEST Taste) und der Buchse „PE“.
Wenn U
C
> U
L
, wobei U
L
die Berührungsgrenzspannung ist (U
L
= 25 oder 50 V: siehe § 3.2: SET-UP),
zeigt das Gerät an, dass die Messung nicht möglich ist.
Wenn eine Messung eingeleitet wird, überwacht das Gerät die Spannung U
NPE
: Wenn diese um mehr
als 20V ansteigt, unterbricht das Gerät den Messvorgang und meldet einen Fehler.
Durch erneute Betätigung der TEST Taste kann die Spannungsmessung wiederaufgenommen
werden.
Bei der Schleifenimpedanzprüfung mit 2 Leitern (Position ZLINE) wird die
Spannungsmessung zwischen Erde und „PE“-Leiter nicht durchgeführt
3.1.3 PRÜFUNG DER MESSBEDINGUNGEN
Für die Freigabe einer Messung müssen zusätzlich zu den vorerwähnten Prüfungen (Bestimmung der
Phasenlage und der Spannung des PE-Leiters) folgende Bedingungen erfüllt sein:
-
U
LN
, U
LPE
und U
NPE
< 550 V,
-
Spannung: f < 450 Hz; Strom: 20 Hz < f < 450 Hz ,
-
Schleifenimpedanzprüfung oder Erdungsprüfung unter Spannung: f = 15,3…65 Hz,
-
ordnungsgemäßer Anschluss der Messkabel (Klemmen angeschlossen und nicht
vertauscht).
Sperrungen des Messvorgangs werden durch eine Fehlermeldung (siehe § 7), einen Piepton
und das blinkende Symbol angezeigt.
Summary of Contents for C.A 6454
Page 3: ...2...