background image

Hurricane™ Haze 2 User Manual 

10/1/2010 5:13 PM

 

1.

 

B

EFORE 

Y

OU 

B

EGIN

 

What is included 

¾

 

1 x Hurricane™ Haze 2 

¾

 

1 x Wired Remote (HH1) 

¾

 

1 x Power Cord  

¾

 

1 x Warranty Card 

¾

 

1 x User Manual 

Unpacking Instructions 

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that 

all parts are present, and have been received in good condition. Notify the shipper immediately and 

retain packing material for inspection if any parts appear damaged from shipping or the carton itself 

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture 

must be returned to the factory, it is important that the fixture be returned in the original factory box 

and packing. 

AC Power 

To determine the power requirements for a particular fixture, see the label affixed to the back plate of 

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average 

current draw under normal conditions. All fixtures must be powered directly off a switched circuit and 

cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer 

channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the 

source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure 

that if a voltage selection switch exists that it is set to the correct line voltage you will use. 

 

Warning! 

Verify that the voltage rating on your unit matches the line voltage applied. Damage 
to your fixture may result if the line voltage applied does not match the voltage 
indicated on the rating. All fixtures must be connected to circuits with a suitable 
Earth Ground.  

Summary of Contents for Hurricane Haze 2

















Reviews: