Charlton & Jenrick PARAGON FOCUS 18 HE Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 32

background image

12

LT5558 (ISS 7)

* Before fitting the pebble set loosen the burner securing screws and make sure that burner is pushed to the right
side of the burner tray. This will ensure maximum aeration to the burner and reduce discolouration.

Pebble Fuel Bed Layout (Refer to warnings at the beginning of this section.)



Locate the Rear Matrix on the burner ensuring that the
front edge is against the back of the burner slot and not
on top of it.



Place the RH and LH Front Matrix in the channel at the
front of the burner tray.



Lay one row of Pebbles as shown.

«
...
10
11
12
13
14
...
»

Summary of Contents for PARAGON FOCUS 18 HE

































Reviews:

No comments

Related manuals for PARAGON FOCUS 18 HE

Brand: Pacific energy Pages: 36

Brand: Superior Pages: 12

Brand: Uniflame Pages: 12

Brand: Napoleon Pages: 20

Brand: Rinnai Pages: 32

Brand: Desa Pages: 32

Brand: Travis Industries Pages: 9

VECTRON GL 05.1000 DUO PLUS

Brand: elco Pages: 52

Fire Ribbon Direct VEnt Slim 26"

Brand: Spark Pages: 48

Mercer CM140-095

Brand: Charmate Pages: 4

Luna Diamond 1000CL

Brand: M Design Pages: 44

Brand: Procom Pages: 16

Brand: British Fires Pages: 48

Brand: baltur Pages: 60

Brand: GRAND EFFECTS Pages: 8

Brand: GRAND EFFECTS Pages: 14

Brand: Grand Canyon Gas Logs Pages: 5

Brand: Sister Bay Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands