background image

15

 

GO ECO Range 

Issue 01.1 05/17

 

Note: Warning!- Petroleum coke fuels or household waste must not be burnt on this 
appliance.  
 
Should any difficulties arise over fuel quality or suitability, consult your local approved fuel 
merchant. 
 

7.7

 

Important Information for Wood Burning  

With a full load of wood and burning near nominal output the stove will need to be refuelled 
approximately every 45 min to 1.5 hours. One or two large logs will burn longer and cleaner 
than a number of smaller ones. Wood can usually be stacked higher in the stove than solid 
mineral fuel but care must be taken that logs do not touch the baffle or the glass panel. Do not 
stack logs above the level of the rear firebox liner brick at the back of the stove. 
 
Always make sure that flames are visible above the wood after re-fuelling for cleanest burning. 
Burning without flames above the fuel will create unnecessary smoke and poor heat output
After re-fuelling open the air wash control fully to the right side for 3 minutes or until the logs 
are fully blackened to achieve full flames above the fuel.
 
 
Wood burns well on a bed of ash and it is therefore only necessary to remove surplus ash from 
the stove occasionally. 
Burn only dry, well-seasoned wood, which should have been cut, split and stacked - under cover 
from rain - for at least 12-24 months with free air movement around the sides of the stack to 
enable it to dry out. Burning wet or unseasoned wood will create tar deposits in the stove and 
chimney and will not produce a satisfactory heat output. Wood that is not properly dry (‘dry’ is 
considered to be less than 20% internal moisture content) uses up energy from the burn 
process to evaporate the water inside the wood thus creating very poor conditions for 
combustion
. The main cause of burning problems with wood stoves is due to excessively damp 
wood. Wood can appear perfectly dry on the outside but still contain 40-50% water on the 
inside. A moisture meter can be purchased from stove and equipment suppliers if you wish to 
check your wood source is correct. Split a log and check the inside as well as the outside. 
 

7.7.1

 

Refuelling on to a low fire bed  

If there is insufficient burning material in the firebed to light a new fuel charge, excessive smoke 
emission can occur. Refuelling must be carried out onto a sufficient quantity of glowing embers 
and ash so that the new fuel charge will ignite in a reasonable period. If there are too few 
embers in the fire bed, add suitable kindling and firelighter if necessary to prevent excessive 
smoke.  
 

7.7.2

 

Fuel overloading  

The maximum amount of fuel specified in this manual should not be exceeded, overloading can 
cause excess smoke. Never load fuel above the back firebrick firebox liner or allow them to 
touch the glass. All models max log diameter = approx. 150mm. Max length = 250mm for 5 and 
5 plus, 350mm for 5 Wide and 5 Wide Plus models. One log is acceptable ONLY if loading onto a 
hot, well established fire bed. 
 

7.7.3

 

Operation with door left open  

Operation with the door open can cause excess smoke and spillage into the room. The 
appliance must not be operated with the appliance door left open. 
 
 
 

Summary of Contents for GO ECO 5Kw

























Reviews: