background image

 

 

Contents 

 

EXTENDED FIVE YEAR PARTS WARRANTY .................... 2 

Benchmark Scheme ..................................................... 3 

SECTION ONE Introduction (Users Instructions)

 ........ 5 

SECTION TWO Operating the Appliance (Users 
Instructions)

 ................................................................. 7 

SECTION THREE Cleaning (Users Instructions)

 ........... 8 

SECTION FOUR Fuel Bed Cleaning and Layout (Users 
Instructions)

 ................................................................. 9 

Log fuel bed layout

 .................................................. 9 

SECTION FIVE General Points (Users Instructions)

 ... 13 

SECTION SIX Appliance Data (Installation 
Instructions)

 ............................................................... 13 

Appliance Dimensions

 ........................................... 15 

SECTION SEVEN Regulations and Warnings 
(Installation Instructions)

 .......................................... 16 

SECTION EIGHT Siting the Appliance (Installation 
Instructions)

 ............................................................... 17 

General Requirements

 .......................................... 17 

SECTION NINE Preparing the Appliance for Installation

 ................................................................................... 18 

SECTION TEN Installing the Appliance (Installation 
Instructions)

 ............................................................... 23 

TIMBER FRAMED DWELLING

 ..................................... 25 

TOP FLUE UP & OUT

 .............................................. 26 

Optional flue lengths

 ............................................. 27 

SECTION ELEVEN connecting the gas supply 
(Installation Instructions)

 .......................................... 27 

SECTION TWELVE Checking Operation of Fire 
(Installation Instructions)

 .......................................... 29 

SECTION THIRTEEN Maintenance (Maintenance 
Instructions)

 ............................................................... 30 

SECTION FOURTEEN Wiring Diagram (Maintenance 
Instructions)

 ............................................................... 32 

SECTION FIFTEEN  Short Spares List

 ........................... 33 

GAS FIRE COMMISSIONING CHECKLIST

 ..................... 35 

SERVICE RECORD

 ....................................................... 36 

 

 

 

 

 

 

EXTENDED FIVE YEAR PARTS 
WARRANTY 

 

In  order  to  validate  your  extended  5  years  parts 
warranty  please  read  the  Benchmark  Scheme  on  the 
opposite page  and ensure your installer has filled in the 
appropriate  checklist.

 

 

This in no way reduces your statutory rights

 

 

Your warranty commences from the date of purchase 
and  you must retain your receipt or invoice as proof of 
a  purchase date. 

 

THIS  EXTENDED  WARRANTY  SPECIFICALLY  EXCLUDES 
GLASS  AND SOFT REFRACTORY COMPONENTS AND ANY 
BATTERIES. 

 

Terms and Conditions 

1.

 

The  appliance  must  be  installed  by  a  GAS  SAFE 
registered person. 

2.

 

The  appliance  must  be  used  in  accordance  with 
the 

user’s

 instructions. 

3.

 

The  appliance  must  be  serviced  annually  by  a  GAS 
SAFE  registered person. 

4.

 

The  benchmark  and  service  log  must  be  correctly 
filled  out and the record of annual services must be up 
to date  and supported by receipts in each case. 

5.

 

This  warranty is  not  transferable  and relates  to  the 
original installation only. 

6.

 

The  appliance has not  been subjected to misuse  or 
accident  or  been  modified  or  repaired  by  any 
person  other  than  the  authorised  employee  or 
authorised  representative  of  Charlton  and  Jenrick 
Ltd. 

7.

 

The  registration  form  must  be  returned  within  1 
month  of purchase. 

8.

 

Technical Help Desk 01952 200 444

 

Summary of Contents for Edge 3s BF









































Reviews: