background image

11

WARNING

For Safe Use Of Your Grill And To Avoid Serious 

Injury:

Do not let children operate or play near grill. 

Keep grill area clear and free from materials that burn.

Do not block holes in bottom or back of grill. 

Check burner flames regularly.

Use grill only in well-ventilated space. NEVER use in 
enclosed space such as carport, garage, porch, covered 
patio, or under an overhead structure of any kind.

Do not use charcoal or ceramic briquets in a gas grill. 
(

Unless

 

briquets are supplied with your grill.)

• Use grill at least 3 ft. from any wall or surface. 

Maintain 

10 ft. clearance to objects that can catch fire or sources of 
ignition such as pilot lights on water heaters, live electrical 
appliances, etc.

• Apartment Dwellers:

Check with management to learn the requirements and fire 
codes for using an LP gas grill in your apartment complex. If 
allowed, use outside on the ground floor with a three (3) foot 
clearance from walls or rails. Do not use on or under 
balconies.

• NEVER attempt to light burner with lid closed. A buildup 

of non-ignited gas inside a closed grill is hazardous.

• Never operate grill with LP tank out of correct position 

specified in assembly instructions. 

• Always close LP tank valve and remove coupling nut 

before moving LP tank from specified operation 

position.

Safety Tips

s

Before opening LP cylinder valve, check the coupling nut for 
tightness.

s

When grill is not in use, turn off all control knobs and LP 
cylinder valve. 

s

Never move grill while in operation or still hot.

s

Use long-handled barbecue utensils and oven mitts to avoid 
burns and splatters.

s

Maximum load for sideburner and side shelf is 10 lbs.

s

s

 

Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.

s

If you notice grease or other hot material dripping from grill 
onto valve, hose or regulator, turn off gas supply at once. 
Determine the cause, correct it, then clean and inspect valve, 
hose and regulator before continuing. Perform a leak test.

s

Keep ventilation openings in cylinder enclosure (grill cart) free 
and clear of debris.

s

Do not store objects or materials inside the grill cart 
enclosure that would block the flow of combustion air to the 
underside of either the control panel or the firebox bowl.

s

The regulator may make a humming or whistling noise during 
operation. This will not affect safety or use of grill.

s

If you have a grill problem see the 

"Troubleshooting Section"

.

s

If the regulator frosts, turn off grill and LP cylinder valve 
immediately. This indicates a problem with the cylinder and it 
should not be used on any product. Return to supplier!

The

 

grease

 

cup

 

must

 

be

 

attached

 

to

 

grease

 

cup

 

clip

 

and

emptied

 

after

 

each

 

use

Do

 

not

 

remove

 

grease

 

cup

 

until

 

grill

has

 

completely

 

cooled

.

CAUTION

• Putting out grease fires by closing the lid is not possible. 

Grills are well ventilated for safety reasons. 

• Do not use water on a grease fire. Personal injury may 

result. If a grease fire develops, turn knobs and LP 

cylinder off. 

• Do not leave grill unattended while preheating or burning 

off food residue on HI. If grill has not been regularly 

cleaned, a grease fire can occur that may damage the 

product. 

Lighting instructions continued on next page.

Ignitor Lighting

s

 

 Do not lean over grill while lighting.

1.

Turn              all burner control valves. 

2.

Turn on gas source or tank.

3. Open lid during lighting.

4.

5.

Push IGNITOR  button rapidly.

6.

 

7.

To ignite, turn IGNITION BURNER knob to        PRE-HEAT. 

If ignition does NOT occur in 5 seconds, turn the burner 
controls              , wait 5 minutes and repeat the lighting 
procedure.
To ignite right burner, turn right knob to PRE-HEAT.

If ignitor does not work, follow match lighting instructions.
After Lighting: Turn knobs to HI position for warm-up. 

Summary of Contents for 463741209

































Reviews: