Char-Broil 463269311 Product Manual Download Page 7

7

WARNING

For Safe Use of Your Grill and to Avoid Serious 
Injury:

Do not let children operate or play near grill. 

Keep grill area clear and free from materials that burn.

Do not block holes in sides or back of grill. 

Check burner flames regularly.

Use grill only in well-ventilated space. NEVER use in 
enclosed space such as carport, garage, porch, 
covered patio, or under an overhead structure of any 
kind.

Do not use charcoal or ceramic briquets in a gas grill. 
(

Unless

 

briquets are supplied with your grill.)

• Use grill at least 3 ft. from any wall or surface. 

Maintain 10 ft. clearance to objects that can catch fire 
or sources of ignition such as pilot lights on water 
heaters, live electrical appliances, etc.

• Apartment Dwellers:

Check with management to learn the requirements 
and fire codes for using an LP gas grill in your 
apartment complex. If allowed, use outside on the 
ground floor with a three (3) foot clearance from walls 
or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A 

buildup of non-ignited gas inside a closed grill is 
hazardous.

• Never operate grill with LP cylinder out of correct 

position specified in assembly instructions. 

• Always close LP cylinder valve and remove 

coupling nut before moving LP cylinder from 
specified operation position.

Safety Tips

Before opening LP cylinder valve, check the coupling nut for 
tightness.

When grill is not in use, turn off all control knobs and LP 
cylinder valve. 

Never move grill while in operation or still hot.

Use long-handled barbecue utensils and oven mitts to avoid 
burns and splatters.

Maximum load for sideburner and side shelf is 10 lbs.

The grease tray 

must 

be inserted into grill and emptied after 

each use. Do not remove grease tray until grill has 
completely cooled.

Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.

If you notice grease or other hot material dripping from grill 
onto valve, hose or regulator, turn off gas supply at once. 
Determine the cause, correct it, then clean and inspect valve, 
hose and regulator before continuing. Perform a leak test.

Keep ventilation openings in cylinder enclosure (grill cart) free 
and clear of debris.

Do not store objects or materials inside the grill cart 
enclosure that would block the flow of combustion air to the 
underside of either the control panel or the firebox bowl.

The regulator may make a humming or whistling noise during 
operation. This will not affect safety or use of grill.

If you have a grill problem see the 

"Troubleshooting Section"

.

If the regulator frosts, turn off grill and LP cylinder valve 
immediately. This indicates a problem with the cylinder and it 
should not be used on any product. Return to supplier!

CAUTION

• Putting out grease fires by closing the lid is not possible. 

Grills are well ventilated for safety reasons. 

• Do not use water on a grease fire. Personal injury may 

result. If a grease fire develops, turn knobs and LP 
cylinder off. 

• Do not leave grill unattended while preheating or burning 

off food residue on HI. If grill has not been regularly 
cleaned, a grease fire can occur that may damage the 
product. 

Ignitor Lighting

 

 Do not lean over grill while lighting.

1.
2.
3.

5.

6.

Turn 

OFF 

all gas burner control valves. 

Turn 

ON

 gas at LP cylinder.

Open lid during lighting.

To ignite any main burner, turn the main burner control

Push and hold 

ELECTRONIC IGNITION

 button until the

7. 

If ignition does NOT occur in 5 seconds, turn the burner 

controls 

OFF

, wait 5 minutes and repeat the lighting 

procedure.

8.

 Repeat steps 4 through 7 for the remaining main burners.

If ignitor does not work, follow match lighting instructions. 

4.

Push in and turn AUTO-CLEAN™ valve to 

GRILL

 position.

knob to the 

HI 

position

burner lights.

9. 

Once each burner has ignited, turn knob to desired setting.

Summary of Contents for 463269311

































Reviews: