background image

For warranty service

CALL TOLL FREE

1-800-232-3398

PREPARING TO USE YOUR GRILL

Before cooking with your grill, the following steps should be closely followed to both cure the finish and season the
interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first
foods.

1. Brush all interior surfaces including grills and grates with vegetable cooking oil.

2. Build a small fire on the fire grate, being sure not to lay coals against the walls.

3. Close lid. Position vents at approximately one quarter open. This burn should be sustained for at least two hours.

Begin increasing temperature by opening the vents half-way and adding more charcoal. Your grill is now ready
for use.

Rust can appear on the inside of your grill. Maintaining a light coat of vegetable oil on interior surfaces will aid in the
protection of your grill. Exterior surfaces of the grill may need occasional touch up. We recommend the use of a
commercially available black high temperature spray paint. NEVER PAINT THE INTERIOR OF THE UNIT !

Wood is recommended, however charcoal or a combination of both may be used as the fuel source for grilling, with
the fuel source placed and ignited on the fire grate. Do not build too large of a fire. We recommend starting a fire
with no more than 4 pounds of charcoal (approximately 60 briquets) and adding more as needed during cooking.
After allowing the fire to burn down, place the cooking grate in the grill. Failure to read and follow instructions for
lighting charcoal may result in serious personal injury and/or property damage.

Frequency of cleanup is determined by how often the grill is used. Make sure coals are completely extinguished
before cleaning inside of grill.

GRILLING

GRILL MAINTENANCE

Thoroughly rinse with water and allow to air dry before using again. Wipe out the

interior of unit with cloth or paper towel.

Limited Warranty

Charbroil warrants the CB 940 Grill for replacement or repair of parts and/or workmanship for a period of 90 days. Charbroil warrants
to the original CB 940 Grill owner repair or replacement of the cooking chamber only should "burn out" or "rust through" occur for a
period of 1 year. Paint is not warranted and will require touchup.

These limited warranties are made exclusively to the original customer presenting proof of purchase. These warranties are limited to
non-commercial usage. Any returned goods must be clearly marked with a Charbroil Return Authorization Number and shipped
prepaid. These limited warranties do not cover normal wear and tear or damages resulting from abuse or misuse. This warranty
excludes incidental or consequential cost due to damages or losses or property of any nature.

NOTICE: Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and
you may also have other legal rights which may vary from state to state.

Summary of Contents for 1309400













Reviews: