background image

9

Réf. : CH - 1254 - I - 0 - EN

6.2 Location

1.

The boiler must be positioned on a flat and level floor
or base which must be capable of supporting the full
operational weight of the boiler. The flue must pass
through an outside roof or wall and discharge to
atmosphere in a position permitting satisfactory
removal of combustion products.

2.

The boiler should be fitted within the building unless
otherwise protected by a suitable enclosure i.e. ga-
rage or outhouse.

3.

If the boiler or any part of the system is located in an
area that may be subjected to low ambient tempera-
tures, it is recommended that a suitable frost protec
tion device is incorporated into the control system.

6.3 Gas Supply

1.

The gas installation should be in accordance with
reglementation.

2.

The connection to the appliance is 1/2" Rp
Do not use pipes of a smaller diameter than the boiler
gas connection

6.4 Electrical Supply

1.

External wiring must be correctly earthed.

2.

The mains supply is 230V ~ 50Hz fused at 3A.

NOTE :

 The method of connection to the electricity supply

must facilitate complete electrical isolation of the
appliance.

Connection may be via a fused double-pole isolator with
a contact separation of at least 3mm in all poles and
servicing the boiler and system controls only.

6.5

Flues & Ventilation

1.

The room or space of installation must be ventilated
to ensure the correct and safe operation of the boiler.

2.

The flue system should be lined throughout its length.

3.

Minimum flue length is 1m. There should be at least
1m of vertical flue from the boiler flue socket, and
horizontal runs and 90°bends should be avoided.

4.

If an existing chimney is used it must be fully swept
before lining or connecting the boiler. Precautions
should be taken to avoid condensation forming in the
flue.

5.

The flue diameter must be at least the same diameter
as the connection on the boiler draught diverter.

6.

The flue terminal must be of an approved type and be
positioned above roof level.

N04358.EPS

Gas
Connection

Summary of Contents for EDENA CLASSIC E 35

























Reviews: