manualshive.com logo in svg

Channel Vision P-0920, Instructions Manual

Share
Download
Channel Vision P-0920 Instructions Manual Download Page 2

2

3

Features:

!

Distinctive telephone ring

!

LED status indicators

!

RJ-45 connections for input and output

!

Compatible with Channel Vision’s DP and IU door stations

The P-0920 must be used together with a compatible door intercom 
station.  Channel Vision offers a variety of compatible units such as the 
popular IU-series and DP-series intercom stations. For example, model 
DP-0212 is compatible.

Important Exceptions:

Channel Vision offers some IU-series and DP-series intercom stations 
that are only compatible with Panasonic KSU phone systems.  These 
model numbers, which end with the letter “P”, will NOT WORK.  For 
example, model DP-0212

P

 is NOT COMPATIBLE.

The P-0920 is installed in-line between your telephone service provider 
and your telephone distribution system.  A compatible door intercom 
station is installed and connected to the P-0920.  When the door 
intercom’s button is pressed, the phones in the house will ring, if the 
phone is answered within 20 seconds you will be automatically connected 
to door intercom station.  If you wish to contact the door intercom station 
after 20 seconds has passed, pick up the phone and dial ** (or ## 
depending your configuration).

If you are using the optional TE110DS door strike relay module, it can be 
activated by dialing the appropriate touch-tone code (see the user’s guide 
section) or by pressing a button that is connected to the “Unlock Door” 
terminals. You can use the “Unlock Door” terminals If you would like to be 
able to open an access gate from outside of the house without using a 
telephone. Simply wire a standard push button to these terminals that will 
provide a momentary short when the button is pressed. 

Use the “Chime” terminals if you would like to use a traditional doorbell 
chime in addition to ringing the telephones when the door intercom button 
is pressed. 

For convenience, there are two different ways to connect the active 
phone line input and telephone output. 
Option 1: connect the active phone using a single pair of wires to the wire 
terminals labeled “CO Input”.  Then connect a single pari of wires to the 
wire terminals labeled “Telephone” and connect the other end of those 
wires to your telephone distribution wiring system.
Option 2: use the RJ-45 jacks to connect the “CO Input” and “Telephone” 
output. This option simplifies wiring because CAT5 jumper cables can be 
used to interconnect the P-0920 with other Channel Vision telephone 
modules.

Compatibility

How it Works

Wiring Options

The

 P-0920

 is a telephone entry controller that works with Channel 

Vision’s IU and DP series door stations to create an elegant door 
intercom system.  When the doorbell button is pressed, the phones will 
ring.  Simply answer the phone and you will be able to speak to the 
person at the door.

Phone line in from the service provider CO (Central Office).

Dry contact that closes when the doorbell button is pressed.

Configuration switches 
(see basic setup).

RJ-45 input for CO lines and output to Telephones.
These allow pass-through of 4 telephone lines. 
Note: only line 1 is affected by the telephone entry controller.
Important: The RJ-45 input and output cannot be used if 
there is a CO line connected to the wire terminal input.

Connect a standard push-button.  When the button is pressed 
the door strike relay will be activated.  
Note: TE110DS is sold separately.

Connect a compatible door intercom station.

Ring LED
Flashes when phones ring.
Intercom Active LED
Lights when door 
intercom station is in use.

Strike Active LED
Lights when the door 
strike relay has been 
activated.

Connect the 12VAC power supply (included).

Output to telephones.

Strike

Active

Ring

Intercom

Active

12VAC

#

o

r

*

N

o

 C

O

Strike
Time

3

/5

 r

n

g

1

2

3

Power

Intercom

Unlock 

Door

Chime

CO Input

Phones

TELEPHONE ENTRY CONTROLLER

CO Input

Telephones

Model 

P-0920

PRO

C

H A N N E L 

TM

V

I S I O N

C

H A N N E L 

V

I S I O N

TM

Summary of Contents for P-0920













Reviews:

No comments

Brands by name

Popular brands

Load more brands