Channel Master 1.8m Offset Tx/Rx Antenna System Instruction And Assembly Manual Download Page 2

VSAT ANTENNA/MOUNT/LNB

LIMITED TWELVE (12) MONTH WARRANTY

This CHANNEL MASTER

®

equipment is warranted to be free from defects in material and workmanship under normal

use and service. CHANNEL MASTER shall repair or replace defective equipment, at no charge, or at its option, refund the
purchase price, if the equipment is returned to CHANNEL MASTER not more than twelve (12) months after shipment.
Removal or reinstallation of equipment and its transportation shall not be at the cost of CHANNEL MASTER except
CHANNEL MASTER shall return repaired or replaced equipment freight prepaid.

This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect its stability or
durability, or which has been subject to misuse, negligence or accident. This Warranty does not cover equipment which has
been impaired by severe weather conditions such as excessive wind, ice, storms, lightning, or other natural occur-
rences over which CHANNEL MASTER has no control, and this Warranty shall not apply to equipment which has been
operated or installed other than in accordance with the instructions furnished by CHANNEL MASTER.

Claimants under this Warranty shall present their claims along with the defective equipment to CHANNEL MASTER imme-
diately upon failure. Non-compliance with any part of this claim procedure may invalidate this warranty in whole or in part.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY. CHANNEL MASTER DOES NOT AUTHORIZE ANY PERSON TO ASSUME FOR IT
THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND CHANNEL MASTER NEITHER ASSUMES NOR AUTHO-
RIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION
WITH THE EQUIPMENT DELIVERED OR PROVIDED.

IN NO EVENT SHALL CHANNEL MASTER BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE,
INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.

In no event shall CHANNEL MASTER be liable for damages in an amount greater than the purchase price of the equipment.

Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you.

DATE

DESCRIPTION

REV.

5/03

ECN 9000000

Rel.

Summary of Contents for 1.8m Offset Tx/Rx Antenna System



















Reviews: