background image

2

1.

PRESSURIZED DEVICES:

This equipment is a pressure

containing device.

Do not exceed maximum operating
pressure as shown on equipment serial
number tag.

Make sure equipment is depressurized before
working on or disassembling it for service.

GENERAL SAFETY INFORMATION

2.

ELECTRICAL:

This equipment requires electricity
to operate.

Install equipment in compliance
with all applicable electrical codes.

Standard equipment is supplied with electrical
enclosures not intended for installation in
hazardous environments.

Disconnect power supply to equipment when
performing any electrical service work.

A.

RECEIVING

This shipment has been thoroughly checked, packed
and inspected before leaving our plant. It was
received in good condition by the carrier and was so
acknowledged.

Check for Visible Loss or Damage. If this shipment
shows evidence of loss or damage at time of delivery
to you, insist that a notation of this loss or damage
be made on the delivery receipt by the carrier’s
agent.

B.

UNPACKING

Check for Concealed Loss or Damage. When a
shipment has been delivered to you in apparent good
order, but  concealed damage is found upon
unpacking, notify the carrier immediately and insist
on his agent inspecting  the shipment. Concealed
damage claims are not our responsibility as our terms
are F.O.B. point of shipment.

C.

MOVING

In moving or transporting dryer, do not tip dryer onto
its side.

D. STORAGE/SHUT DOWN

Dryer should not be stored outside (either

packed or unpacked) or exposed to the weather. Damage
to electrical and control components may result.

IMPORTANT: WATER-COOLED UNITS - If unit is shut down
below freezing temperatures, the water-cooled
condenser may freeze and cause permanent damage.
Condenser must be drained when the unit is shut down.

IMPORTANT: Do not store dryer in temperatures above
130

°

F, 54.4

°

C.

3.

BREATHING  AIR:

Air treated by this equipment
may not be suitable for breathing
without further purification.

Refer to applicable standards and
specifications for the requirements for breathing
quality air.

RECEIVING, MOVING, AND UNPACKING

Summary of Contents for CRN Series





















Reviews: