background image

1

  

REV 93020-20120419

ENGLISH

 

93020

INTROdUCTION

Introduction

Congratulations on your purchase of a Champion 
Power Equipment log splitter . CPE designs and builds 
log splitters to strict specifications . With proper use 
and maintenance, this log splitter will bring years of 
satisfying service .

Portable Log Splitter

This unit is a gasoline engine driven hydraulic log splitter . 
It is designed to split wood logs for use as fire wood for 
a stove or fire place . This log splitter will only split logs 
lengthwise, with the grain only .

Record the model and serial numbers as well as date and place of purchase for future reference . Have this information 
available when ordering parts and when making technical or warranty inquiries .

Accessories

Champion Power Equipment manufactures and sells 
accessories designed to help you get the most from your 
purchase . To find out more please visit our website at:
    www.championpowerequipment.com

This Booklet

Every effort has been made to ensure the accuracy and 
completeness of the information in this manual . We reserve 
the right to change, alter and/or improve the product and 
this document at any time without prior notice .

Champion Power Equipment Support

Model Number

Serial Number

Date of Purchase

Purchase Location

1-877-338-0999

93020

For 

Oil Type see “Add Engine Oil” section . For Fuel Type see “Add Fuel” section .

Summary of Contents for 93020
































Reviews: