background image

100306 - 2000W PORTABLE INVERTER GENERATOR

IMPORTANT SAfETY INSTRUCTIONS

8

Operation Symbols

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of 
these symbols will allow you to more safely operate the product.

SYMBOL

MEANING

Engine START

Engine RUN

Engine STOP

STOP or OFF

Run out of fuel. Stopping the 
generator.

Fuel Level

Power Output.

 Percentage of 

available power from generator being 
used.

Remaining Fuel Time

Overload Reset Switch

ECO

Economy Mode Switch

Maintenance Required Indicator

Low Oil Level Indicator

Receptacle Status

Circuit Breaker Reset: Push

Ground Terminal

SYMBOL

MEANING

Neutral Floating. 

Neutral circuit 

IS 

NOT

 electrically connected to the 

frame/ground of the generator.

Parallel Connection(s)

10W-30

Check Oil Level.

 Recommended oil is 

10W-30. The engine can be seriously 
damaged without oil. Always check 
the oil level before using. The 
machine must be resting firmly on 
level ground when checking.

Check Fuel Level.

 Use clean, fresh, 

regular unleaded gasoline with a 
minimum octane rating of 85 and an 
ethanol content of less than 10% by 
volume.

Recoil Starter.

 Pull recoil starter to 

start the engine.

Plug In.

 Plug in desired devices.

Unplug.

 Unplug devices when turning 

generator off.

Summary of Contents for 100306





































Reviews: