Champion Global Power Equipment 500110-N Owner'S Manual & Operating Instructions Download Page 19

16

500110-N

 

ENGLISH

Adjustments

The air-fuel mixture is not adjustable. Tampering with 
the governor can damage your generator and your 
electrical devices and will void your warranty. CPE 
recommends that you contact our service line at
  for all other service and/or adjustment needs.

Maintenance Schedule

Follow the service intervals indicated in the following 
maintenance schedule. 
Service your generator more frequently when operating 
in adverse conditions. 
Contact our helpline at 

  to locate the nearest Champion 

Power Equipment certified service dealer for your 
generator or engine maintenance needs.

Use a damp cloth to clean exterior surfaces of the engine.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris 
from the engine.

Cleaning

DO NOT spray engine with water.

CAUTION

Water can contaminate the fuel system.

Spark Arrester

1.  Allow the engine to cool completely before servicing 

the spark arrester.

2.  Remove the three screws holding the cover plate 

which retains the end of the spark arrester to the 
muffler.

3.  Remove the spark arrester screen.
4.  Carefully remove the carbon deposits from the spark 

arrester screen with a wire brush.

5.  Replace the spark arrester if it is damaged.
6.  Position the spark arrester in the muffler and attach 

with the three screws.

Failure to clean the spark arrester will result in degraded 
engine performance.

CAUTION

Federal and local laws and administrative requirements 
indicate when and where spark arresters are required. 
When ordered, spark arresters are required for operation 
of this generator in National Forest lands. In California, 
this generator must not be used on any forest- covered 
land, brush-covered land, or grass- covered land unless 
the engine is equipped with a spark arrester.

NOTE

*To be performed by knowledgeable, experienced owners or 
Champion Power Equipment certified dealers.

MAINTENANCE AND STORAGE

Generator Maintenance

Make certain that the generator is kept clean and stored 
properly. Only operate the unit on a flat, level surface in 
a clean, dry operating environment. DO NOT expose the 
unit to extreme conditions, excessive dust, dirt, moisture 
or corrosive vapors.

Use a damp cloth to clean exterior surfaces of the generator.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris 
from the generator. 
Inspect all air vents and cooling slots to ensure that they 
are clean and unobstructed.

DO NOT use a garden hose to clean the generator.

Water can enter the generator through the cooling 
slots and damage the generator windings.

CAUTION

Every 8 hours or daily

Check oil level

Clean around air intake and muffler

First 5 Hours

Change oil

Every 50 hours or every season

Clean air filter

Change oil if operating under heavy load or in hot 

environments

Every 100 hours or every season

Change oil

Clean/Adjust spark plug

Check/Adjust valve clearance*

Clean spark arrester

Clean fuel tank and filter*

Every 250 hours

Clean combustion chamber*

Every 3 years

Replace fuel line

Summary of Contents for 500110-N





























Reviews: