background image

100416 - 8000W TRI-FUEL PORTABLE GENERATOR

MAINTENANCE

31

 

NOTICE

Federal and local laws and administrative requirements 
indicate when and where spark arrestors are required. When 
ordered, spark arrestors are required for operation of this 
generator in National Forest lands. In California, this generator 
must not be used on any forest-covered land, brush-covered 
land, or grass-covered land unless the engine is equipped with 
a spark arrestor.

Adjusting the Governor

 

WARNING

Tampering with the factory set governor will void your 
warranty.

The air-fuel mixture is not adjustable. Tampering with the governor 
can damage your generator and your electrical devices and 
will void your warranty. Contact our Technical Support Team at 
1-877-338-0999 for all other service and/or adjustment needs.

Generator Battery

Your generator is equipped with an automatic battery charging 
circuit that charges the battery while the engine is running. 
The battery will maintain a proper charge if the unit is used on 
a regular basis (about once every two weeks). If it is used less 
frequently, the battery should be connected to a trickle charger 
or battery maintainer (not included) to keep the battery properly 
charged. 

Maximum charging rate should not exceed 1.5 amps. Follow 
the instructions included with the battery charger. The battery 
should be fully charged at least once per month. If the battery is 
not able to start the engine, it can be started by manually pulling 
the engine recoil cord. If the battery voltage is extremely low, the 
charging circuit may not be able to re-charge the battery. In this 
case, the battery must be connected to a standard automotive 
style battery charger for re-charging before it can be used.

Disconnect the Battery

1.  Pull two halves of battery connector apart.

Charge the Battery

For a generator equipped with batteries for electric starting, 
proper battery maintenance and storage should be followed. 
A trickle charger or battery maintainer should be used to charge 
the battery while the generator is in storage. Maximum charging 
rate should not exceed 1.5 amps. Follow the instructions included 
with the trickle charger or battery maintainer. The battery should 
be fully charged at least once per month.

Maintenance Schedule

Follow the service intervals indicated in the following maintenance 
schedule. 

Service your generator more frequently when operating in adverse 
conditions. 

Contact our Technical Support Team at 1-877-338-0999 to locate 
the nearest CPE certified service dealer for your generator or 
engine maintenance needs.

EVERY 8 HOURS OR PRIOR TO EACH USE

 

—

Check oil level

 

—

Clean around air intake and muffler

 

—

Check propane (LPG) hose for leaks

FIRST 5 HOURS (BREAK IN)

 

—

Change oil

Summary of Contents for 100416










































Reviews: