manualshive.com logo in svg

Champion Global Power Equipment 100416, Operator'S Manual, Page: 13 / 41

Share
Download
Champion Global Power Equipment 100416 Operator'S Manual Download Page 13

100416 - 8000W TRI-FUEL PORTABLE GENERATOR

CONTROLS AND FEATURES

13

Control Panel

1. 

Ignition Switch

 – Used for electric starting of the generator.

2. 

EZ Start Dial 

– Used to select and turn on gasoline, propane 

(LPG), or natural gas (NG) fuel source. 

3. 

Intelligauge with CO Shield

®

 – Four mode digital meter for 

displaying voltage, frequency, session run time, total run time. 
Mutli-colored LED indicates CO shutoff or fault.  

4. 

Circuit Breakers (Push Reset)

 – Protects the generator 

against electrical overloads.

RECEPTACLES

A

W

120V AC, 30A Locking (NEMA L5-30R)

 

May be used to supply electrical power for 
operation of 120 Volt AC, 30 Amp, single phase, 
60 Hz electrical loads.

B

Y

120/240V AC, 30A Locking (NEMA L14-30R) 

May be used to supply electrical power for 
operation of 120/240 Volt AC, 30 Amp, single 
phase, 60 Hz electrical loads.

C

C

(4×) 120V AC, 20A GFCI (NEMA 5-20R)

 

May be used to supply electrical power for 
operation of 120 Volt AC, 20 Amp, single phase, 
60 Hz electrical loads.

1

3

4

2

A

B

C

EZ Start Dial

Propane-Natural Gas (LPG-NG) Selector

1. 

Propane / Natural Gas (LPG/NG) Run Position

2. 

Propane/Natural Gas (LPG/NG) Choke Position

3. 

Engine Stop

4. 

Gasoline Choke Position

5. 

Gasoline Run Position

1. 

Propane (LPG) Position

2. 

Natural Gas (NG) Position

1

1

2

4

5

2

3

Summary of Contents for 100416










































Reviews:

No comments