Chamberlain PowerLIft CS110MYQ Installation And Operating Instructions Manual Download Page 15

Page: 15 / 28

Featuring MyQ

Technology.

This Users Guide will help get the most from your Chamberlain MyQ

enabled Opener when using a

smartphone, tablet or computer to monitor and control your garage door opener.

The MyQ

Gateway System will operate with CHAMBERLAIN products identified as MyQ

ENABLED.

MyQ

Gateway is an accessory feature and openers will operate as normal with remote controls, whether the MyQ

Gateway is

connected or not.

•

The Internet Gateway System:

is designed to operate with Chamberlain Sectional and Rolling Garage Door openers, and all

the SAFETY INSTRUCTIONS detailed in the OPENER HANDBOOK need to be observed.

•

Unattended Operation:

The Gateway System allows operating the door via an internet enabled product, without visual

monitoring. Never allow anyone to pass through, or leave obstacles in the area of a moving garage door. Persons, pets and

vehicles should remain clear until the door has completely stopped.

• Automatic door:

The door may operate unexpectedly, therefore do not allow anything to stay in the path of the door.

• Safety Beams:

For SAFE operation of the door, Safety Beams MUST BE INSTALLED (refer section 23) and be fully

functional. The door will not operate if the Safety Beams are not functional.

• Tilt Doors:

The Gateway System MUST NOT be used on Tilt doors.

• Do not allow children to play near the door, or with any door controls, including remotes, Smartphones, Tablets or any internet

device that has a Chamberlain MyQ

app installed.

• Power Pack:

It is important to use the AC/DC PowerPack supplied with the product. If the power pack is damaged or

becomes unserviceable, it must be replaced with an ANZ Compliant product, of the same electrical performance.

INSTALLATION INSTRUCTIONS

A . BEFORE YOU BEGIN:

you must have -

• A Chamberlain Enabled garage door opener. (MyQ

enabled)

• A home Router, with an active Broadband internet connection.

• Internet Gateway Kit (contents are listed below)

• MyQ

Internet Gateway Module 828 AU

• 5 VDC Power Pack

• Ethernet cable

• Safety Beams 774AML with assembly instructions

• MyQ

Quick Start Guide

• Chamberlain Internet Gateway Installer/Users Guide

B. INSTALLATION PROCESS:
• Garage Door opener:

Install the Chamberlain Garage Door Opener to a fully functional door using the Installation Instructions supplied with the

product.

• Protector Safety System:

Install the Chamberlain Protector System supplied with the MyQ

Gateway kit, using the Installation Instructions supplied with

the product.

Note:

The Safety Beams must be installed and operational for MyQ

to function.

•

MyQ

Gateway:

Connect & Create the MyQ

Gateway using the following process.

CHAMBERLAIN MYQ GATEWAY INSTALLION & USER GUIDE

MYQ GATEWAY INSTALLATION

WARNING:

Important Safety Instructions:

To prevent possible serious injury/death, or property damage read and follow all instructions carefully.

Summary of Contents for PowerLIft CS110MYQ





























Search results

Summary of Contents for PowerLIft CS110MYQ

Reviews:

Related manuals for PowerLIft CS110MYQ

Brands by name

Popular brands

Chamberlain PowerLIft CS110MYQ, Installation And Operating Instructions Manual

Search results

Summary of Contents for PowerLIft CS110MYQ

Reviews:

Related manuals for PowerLIft CS110MYQ

Brands by name

Popular brands