13
Power and Adjustments
Section 1
8
- Connect Power
To avoid installation diffi culties, do not activate the garage door opener of this time.
To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third
grounding pin. This plug will only t into a grounding type outlet. If the plug doesn’t t into your outlet,
contact a quali ed electrician to install the proper outlet.
1. Plug in the garage door opener into a grounded outlet.
2. DO NOT run garage door opener at this time.
To prevent possible SERIOUS or DEATH from electrocution or re:
• Be sure power is NOT connected to the opener and disconnect power to circuit BEFORE
removing cover to establish permanent wiring connection.
• Garage door installation and wiring MUST be in compliance with ALL local electrical and
building codes.
• NEVER use an extension cord, 2-wire adapter or change plug in ANY way to make it t outlet. Be
sure the opener is grounded.
TYPICAL WIRING
Section 1
9
- Ensure the Door Control is Wired Correctly
If the door control has been installed and wired correctly, the LED behind the push button will blink.
RED
WHITE WHITE GREY
Push
Button
Section
20
- Introduction
Your garage door opener is designed with electronic controls to make setup and adjustments easy. The
adjustments allow you to program where the door will stop in the open (UP) and close (DOWN) position.
The electronic controls sense the amount of force required to open and close the door. The force is
adjusted automatically when you program the travel.
NOTE: If anything interferes with the door’s upward travel it will stop. If anything interferes with
the door’s downward travel, it will reverse.
Without a properly installed safety reversal system, persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage door.
• Incorrect adjustment of garage door travel limits will interfere with proper operation of safety
reversal system.
• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST
reverse on contact with 3.8 cm high object (or 2x4 laid
fl
at) on
fl
oor.
To prevent damage to vehicles, be sure fully open door provides adequate clearance.
UP (Open)
DOWN (Close)
PROGRAMMING BUTTONS
The programming buttons are located on the left or back side panel of the garage door opener and are
used to program the travel. While programming, the UP and DOWN buttons can be used to move the
door as needed.
UP Button
Adjustment
Button
DOWN Button
PROGRAMMING BUTTONS
Summary of Contents for LM-W8ME
