Chamberlain LiftMaster TAC1 Installation And Programming Manual Download Page 18

Page: 18 / 20

TELEPHONE PROGRAMMING

PROGRAMMING

NUMBER

DESCRIPTION OF TASK

FACTORY

SETTING

PROGRAMMING PROCEDURE

**01

Enable Call Forwarding

Disabled

**01

**02

Disable Call Forwarding

**02

**03

Enable Intercom Mode

Disabled

**03

**06

Verify Call Forwarding Number
(Via Caller ID)

Disabled

**06

**07

Enable Telco Mode

Disabled

**07

**#8

Erase Call Forwarding Number

**#8

**10

Adjust “Pick-Up” Ring Count

**10 + Ring Count (2-5)

**13

Enable Alternate DTMF
Programming

Disabled

**13

**14

Enable Standard (Long) Ring
Tone

**14

**15

Enable Alternate (Dual) Ring
Tone

Enabled

**15

#*16

Disable Alternate DTMF
Programming

**16

*# Call

Forwarding

Number #

Enter Call Forwarding
Telephone Number

*# + Telephone Number (Up to 14 digits) + #

DIRECT COMMANDS FROM THE LOCAL TELEPHONE

PROGRAMMING

NUMBER

DESCRIPTION OF TASK

FACTORY

SETTING

PROGRAMMING PROCEDURE

Triggers Relay 2

Triggers Relay 1

**04

Enable Party (Latched) Mode
Relay 1

**04

**05

Disable Party (Latched) Mode
Relay 1

**11

Enable “Do Not Disturb” Mode

Disabled

**11

**12

Disable “Do Not Disturb” Mode

**12

DIRECT COMMANDS FROM THE FORWARDED TELEPHONE

PROGRAMMING

NUMBER

DESCRIPTION OF TASK

FACTORY

SETTING

PROGRAMMING PROCEDURE

Accepts Call From The Unit

Triggers Relay 2

Triggers Relay 1

NOTE:

Keypad commands are to be entered in a single string to result in success (indicated by double high success tone). Stop and go

keystrokes will result in negative tones (low single and triple fail tones).

NOTE:

Use the STAR Key “*” to cancel any input.

PROGRAMMING

>> QUICK REFERENCE

Summary of Contents for LiftMaster TAC1





















Search results

Summary of Contents for LiftMaster TAC1

Reviews:

Related manuals for LiftMaster TAC1

Brands by name

Popular brands

Chamberlain LiftMaster TAC1, Installation And Programming Manual

Search results

Summary of Contents for LiftMaster TAC1

Reviews:

Related manuals for LiftMaster TAC1

Brands by name

Popular brands