manualshive.com logo in svg

Chamberlain LiftMaster Professional SW420, Owner'S Manual

Share
Download
Chamberlain LiftMaster Professional SW420 Owner'S Manual Download Page 23

23

CONTROL BOARD PROGRAMMING AND FEATURES

MOTOR LEARN FUNCTION (FORCE PROFILE)

This function is preprogrammed at factory. If either board or 
motor is replaced, the controller will need to be programmed to 
“LEARN” the specific motor RPM profile of your operator. Switch 
“S3” is provided for this. This is important for accurate force 
control. Failure to do so may result in improper and unsafe 
operation.

To learn the motor:

NOTE:

 Motor Learn must be performed in stand alone mode.

1.  The operator must remain attached to the gate throughout the 

entire process.

2.  Press the motor learn button. The yellow LED should start to 

flash rapidly.

3.  Install a jumper on either the hard open or the hard close input 

terminals. The motor will run for a few seconds and then stop. 
If the LED goes out the motor is learned. If the unit activates a 
limit before completing the learn or some other error occurs 
the LED will go back to on continuously. If this happens try 
learning while running in the opposite direction.

  

NOTE:

 It is important that the jumper is in constant contact 

while the gate is moving in learn mode.

FORCE CONTROL

Set the force control pot such that the unit will complete a full 
cycle of gate travel but can be reversed off an obstruction without 
applying an unreasonable amount of force. On most operators 
this will be around the middle of the range.

NOTE:

 For LED location refer to illustration on previous page.

DIAGNOSTICS (LEDS AND CODES)

There are three diagnostic LEDs. Two red LEDs (OLS, CLS) are 
indicators for the open and close limits. The LEDs are illuminated 
when the limit switch contacts are closed.

The third amber LED (DIAG) is used to blink out diagnostic 
codes. The number is the count of the number of times the LED 
is on in an 8 second period. The LED is on for approximately 1/2 
second and repeats every second until the number is reached. 
There will be a pause following each pulse cycle (1-6 pulses) to 
differentiate between the different diagnostic codes.

MOTOR LEARN BUTTON

FORCE CONTROL

A D J U S T M E N T

LED Code 

Diagnostic Meaning 

Cleared By

Flashed

 

OFF Normal 

operation 

N/A

 

1 

 Single entrapment sensed 

Control Input

 

2 

Double entrapment 

 Hard Input*

 

3 

Failed or no hall 

Removal of

  

effect 

sensor 

problem

 

4 

Exceed maximum motor 

Hard Input*

  

run 

time

 

5 

Limit fault 

 Control Input

 

6 

Loss of communications 

Removal of

 

 

 between master and 

problem

second during run mode

  On No 

Motor not learned 

Completion

 Flash 

 

 

of 

Motor 

Learn Routine

* Hard inputs include open override, close override and 

stop inputs.

Max

Min

Force Control

Motor
Learn
Button (S3)

Summary of Contents for LiftMaster Professional SW420





































Reviews:

No comments

Brands by name

Popular brands

Load more brands