manualshive.com logo in svg

Chamberlain LiftMaster Professional SW420, Owner'S Manual

Share
Download
Chamberlain LiftMaster Professional SW420 Owner'S Manual Download Page 11

11

PEDESTAL MOUNTING

1.  Locate and anchor pedestal. Pedestal should be parallel and 

square to the gate. 

IMPORTANT NOTE:

 The distance between mounting pedestal and 

the relative location of the operator to the gate and fence is 
critical.

2.  Locate electrical conduit, as required, prior to pouring 

concrete.

3.  Bolt the mounting brackets to the pedestal.

4.  Secure the operator to the pedestal by dropping it onto the 

pedestal and allowing the mounting studs to slip through the 
holes on the pedestal brackets. Secure with hex nuts provided.

Figure 1

Figure 2

I N S T A L L A T I O N

26"

14"

26"

14"

Fence Line

Hinge Pin

Pivot

 Gate

Fence Line

Hinge Pin

Pivot

 Gate

Parallel Mount

Pedestal 24" Deep 
In-Ground Minimum

Power and Control Wiring 
Should Be Run In Separate 
Conduit

Pedestal Mount Kit 65RSWP

Concrete Pad

Perpendicular Mount

2" to 4" 
(5.1 to 10.2 cm) 
Above Grade

Depth Required By 
Local Codes or 
Below Frost Line

Bolt (4x) From Bracket to Pedestal

Nut (8x)

Summary of Contents for LiftMaster Professional SW420





































Reviews:

No comments

Brands by name

Popular brands

Load more brands