manualshive.com logo in svg

Chamberlain LiftMaster Professional SW420, Owner'S Manual

Share
Download
Chamberlain LiftMaster Professional SW420 Owner'S Manual Download Page 14

14

NOTE:

 Calculated using NEC guidelines. Local codes and 

conditions must be reviewed for suitability of wire installation. All 
power wiring should be dedicated and protected. Location of 
primary power disconnect should be labeled.

SINGLE PHASE

  115 Vac 

230 Vac

W I R I N G

To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the  

 

  operator MUST not be performed until disconnecting the  

 

  electrical power and locking-out the power via the operator    
  power switch. Upon completion of maintenance the area  

 

  MUST be cleared and secured, at that time the unit may be    
  returned to service.
•  Disconnecting power at the fuse box BEFORE proceeding. 

Operator MUST be properly grounded and connected in 
accordance with local electrical codes. 

NOTE:

 The operator 

should be on a separate fused line of adequate capacity.

•  ALL electrical connections MUST be made by a qualified 

individual.

• DO NOT install any wiring or attempt to run the operator  

 

  without consulting the wiring diagram. We recommend that    
  you Install an optional reversing edge BEFORE proceeding    
  with the control station installation.
• ALL power wiring should be on a dedicated circuit and well    
  protected. The location of the power disconnect should be    
  visible and clearly labeled.
• ALL power and control wiring MUST be run in separate
 conduit.
• BEFORE installing power wiring or control stations be sure to  
  follow all specifications and warnings described below. Failure  
  to do so may result in SEVERE INJURY to persons and/or  

 

  damage to operator. 

ATTENTION

AVERTISSEMENT

AVERTISSEMENT

AVERTISSEMENT

WARNING

CAUTION

WARNING

WARNING

WARNING

PRECAUCIÓN

ADVERTENCIA

ADVERTENCIA

ADVERTENCIA

POWER WIRING INSTALLATION

Wiring Specifications (STRANDED COPPER WIRE)

On a Dual Gate System, each unit must be installed on
ITS OWN separate circuits

WIRE GAUGE 6

•  1/3 HP Motor –––––––––––  

615ft. 

3077ft.

WIRE GAUGE 8

•  1/3 HP Motor –––––––––––  

432ft. 

1942ft.

WIRE GAUGE 10

•  1/3 HP Motor –––––––––––  

271ft. 

1218ft.

WIRE GAUGE 12

•  1/3 HP Motor –––––––––––  

170ft. 

763ft.

Summary of Contents for LiftMaster Professional SW420





































Reviews:

No comments

Brands by name

Popular brands

Load more brands