en-7
PROGRAMMING OF CONTROL
The control is programmed by use of the display. The keys and switches on the right side next to the display are required.
Switch 1:
ON = necessary for programming the control
OFF = locks
Switch 2:
ON = display illumination on
OFF = out
Key SET:
saves current setting
Key UP & DOWN: changes setting
Key NEXT:
to change to different menu / program
DISPLAY INDICATION:
P… =
display of currently accessed menu / program
Def. =
“DEFAULT” factory setting. Ex factory setting
Now =
“NOW” current setting
Yes
“YES”
No
“NO”
n
o
i
t
p
i
r
c
s
e
D
y
a
l
p
s
i
D
Range
My settings
P1
P1= Motor Type
Def: 0 Now: 0
motor type
Setting of applied motor: 0 = no motor
1 = Chamberlain/ LiftMaster; for others: see description
0 - 3
P2
P2 = M1 Travel Time
Def: 5 Now: 5.0s
9
9
-
0
)
s
d
n
o
c
e
s
(
r
o
t
o
m
f
o
n
o
i
t
a
r
u
d
l
e
v
a
r
t
t
e
S
n
o
i
t
a
r
u
d
l
e
v
a
r
t
P3
P3 = Auto Cls Delay Def: 1
Now: 1.0s
automatic closing
Duration in seconds of door in open position
ATTENTION: only in connection with photo cell(s)
0 - 99
P4
P4 = M1 Force Adj
Def: 50% Now: 50%
force setting
Motor force
30 - 100%
P5
P5 = Slow Down
Def: 3 Now: 3.0s
slow travel
end
0
1
-
0
N
W
O
D
–
r
o
o
d
e
r
o
f
e
b
s
d
n
o
c
e
s
n
i
l
e
v
a
r
t
w
o
l
S
P6
P6 = M1 Soft Start
Def: 0 Now: 0.5s
slow travel
start
0
1
-
0
t
r
a
t
s
r
e
t
f
a
s
d
n
o
c
e
s
n
i
l
e
v
a
r
t
w
o
l
S
P7
P7 = Back Up Timer
Def: 0 Now: 0.0s
automatic closing
special
Only in conjunction with program 3: closes door automatically
even after power cut. Time in seconds. Attention: only with connected
photo cell(s)
0 - 65
P8
P8 = Open PE Type
Def: RLY Now: RLY
photocell open-
direction
Preselection of photo cell type: RLY – relay photo cell
PLS – pulse (Chamberlain photo cell 770E and 771E)
RLY - PLS
P9
P9 = Close PE Type
Def: RLY Now: RLY
photocell close-
direction
Preselection of photo cell type: RLY – relay photo cell
PLS – pulse (Chamberlain photo cell 770E and 771E)
RLY - PLS
P10
P10 = PE Reverse
Def: Yes Now: Yes
photocell closed-
reaction
"YES"= gate reverses to open
"NO"= gate stops
No - Yes
P11
P11 = Opn PE ReOpen
Def: No Now: No
photocell open-
reaction
During interruptiongate stops. After clearance "NO" = reverses (closes);
"YES" = opens further
No - Yes
P12
P12 = PED Travel
Def: 5 Now: 5.0s
Pedestrian travel
duration
Travel duration of motor during pedestrian function (in seconds)
0 - 99
P13
P13 = PED Auto Close
Def: No Now: No
Pedestrian
automatic closing
Duration in seconds of gate in open position. P3 must be active.
Attention: only in connection with photocells
No - Yes
P14
P14 = Pwr Fail Close
Def: No Now: No
power cut
behaviour
Closes gate automatically even after power failure. Time in seconds.
Attention: only with connected photocells
No - Yes
P15
P15 = Motor Speed
Def: 10 Now: 10
speed
Speed of gate. Note: by reducing, the max. pulling force cannot be
reached
1 - 10
P16
P16 = ExtraOpnTime
Def: 2 Now: 2.0s
travel duration open
additional
Additional travel duration of motor to compensate for wind or bad
conditions.
0 - 10
P17
P17 = ExtraClsTime
Def: 2 Now: 2.0s
travel duration
close-additional
Additional travel duration of motor to compensate for wind or bad
conditions.
0 - 10
P18
P18 = Battery Type
Def: 24 Now: 24
battery type
2x 12V, no setting possible
24V
P19
P19 = BatteryLowOpn
Def: No Now: No
battery
state of charge
"NO"= gate will not open if battery is empty
"YES"=gate will open, but not close
No - Yes
P20
P20 = RPM Sense
Def: No Now: No
RPM
sensor
"YES" = RPM sensor is connected (necessary in the EU) "NO" = if
nonexistant and if battery is used
No - Yes
P21
P21 = Total Cyles
#Cycles = 0000000
cycle counter
complete
counts all full (completed) cycles
P22
P22 = Resettable Cycl
#Cycles = 000000
cycle counter
resettable
counts complete cyles since last reset
P23
P23 = Reset Cycles
Def: No Now: No
cycle counter reset
Reset P22 cycle counter
P24
P24 = Reset Default
Def: No Now: No
factory setting
RESET
re-establishes factory settings (not P22)
P25
P25 = Software Rev
Revision …..
software
indicates installed software version
1
2
ON
O
FF
ON
O
FF
NEXT
UP
DOWN
SET
Summary of Contents for LiftMaster Professional CB224
Page 47: ...NOTES ...
Page 48: ...709469B Chamberlain GmbH 2009 ...
