3
LIMIT SWITCH
The internal limit switch of the ART turns the drive off when the preset
point is reached. Remove the cover of the drive unit and release the
operator. Manually move the gate into the “OPEN” position and define
the endstop of the angle with the cam. Turn the cams until the desired
end point has been reached. Check which cam has which function (e.g.
upper cam opens gate).
Position of the operator:
Moving the gate clockwise, the endstop has to be defined with the
upper cam.
Moving the gate anticlockwise, the endstop has to be defined with the
lower cam.
See picture
11D
Upper cam = connection 3/4
Lower cam = connection 4/5
Switch the drive on, let it run until the desired point is reached and
interrupt the current with the aid of the main switch. Now turn the limit-
switch dial to the microswitch trigger point.
Most control units have a time function. This should always be set 3 - 5
seconds more than the time actually required. The preliminary setting
should be made for more than this to allow a safety margin. After the
necessary adjustments to the system have been made, the time can be
set more accurately.
NB: The drive works more slowly under windy
conditions.
SAFETY MEASURES
A WING GATE OPENER SHOULD ALWAYS BE OPERATED IN
CONJUNCTION WITH CONTACT STRIPS AND / OR LIGHT
BARRIERS AS SAFETY FEATURES.
Please ensure that you comply with the standards, regulations and
safety devices applicable to your particular case.
Should the force generated by the moving wing at its
closing edge exceed 400 N, additional safety features must
be fitted suitable for the application.
FINAL REMARKS
Arrange the handover of the wing gate opener with your customer Make
sure that persons will operate the gate are familiar with its functions and
can operate them without problems. Have your customer practice
operating the gate until he is fully acquainted with all the following:
• Main switch.
• Rules of operation (e.g. do not drive through while the gate is still
opening).
• Additional safety features (photoelectric barrier, contact strip, flashing
lights, etc.).
• Switch to manual operation in case of power failure.
• Provide the customer with a full set of instructions. Inform him to keep
them in a safe place and read them when possible.
• Reference a checklist, so that you have a record of which functions
have been explained and of any points not dealt with.
ACCESSORIES
Model 94335E
3-channel mini transmitter, 433.92MHz
Model 9747E
Keypad, 433.92MHz
Model 760E
Key switch
Model 100027
1-Function Keyswitch, surface mount
(Flush mount - 100010)
Model 100041
2-Function Keyswitch, surface mount
(Flush mount - 100034)
Model 100263
Infrared barrier
Model 203285
E-Lock 12 Volt
Model 203292
Loop Detector 1 Channel
Model 203308
Loop Detector 2 Channel
Model 203315
Standard Hardstop
Model 203322
Hard Stop High
Model 203339
Mechanical Floor Lock for Double Wings
Model 600008
IR Sensor Stand - 530mm
Model 600015
Key Switch Stand - 1100mm
Model 600046
2.5 Safety Edge Set (Small)
Model 600053
20m Bulk Pack Safety Edge Profile (Small)
Model 600060
Assembly Pack Safety Edge (Small)
Model 600077
Bulk pack (not shown)
Model 600091
Main switch
Model 600138
20m Bulk Pack Safety Edge Profile (Medium)
Model 600145
20m Bulk Pack Safety Edge Profile (Large)
Model 600152
Assembly Pack Safety Edge
(Medium/Large)
Model 600169
1m (3.2 ft.) Safety Edge Profile (Medium)
Model 600176
1m (3.2 ft.) Safety Edge Profile (Large)
Model 600213
Interface Box for Safety Edges
TECHNICAL DATA
Modell
ART300-24MB
Voltage in
VAC 230V AC/24AC/24VDC
Voltage out (Motor)
VDC 24
Power
W 60
Current (max)
A
22
Current (no load current)
A
0,5
Torque
Nm 250
Motor speed
RPM 2200
Travel speed
cm/s 25
Duty cycle (max)
Cycles/h 50
Working temperature range
deg C -20°C/+55°C
Protection class
I
Degree of protection
IP 44
Weight
Kg 9
Max. gate wing lenght
m 2,5
Max. gate weight at max. wing lenght
Kg 300
incl. 20% reserve
709445
©, 2006
