Chamberlain 4210E, Instructions Manual

Page: 24 / 114

ACCESSORIES –
433MHz 27MHz
(1) Models 4330E 750E Single-Function Remote Control
(2) Models 4332E 752E 2-Function Remote Control
(3) Model 4333E 3-Function Remote Control
(4) Model 754E 4-Function Remote Control
(5) Model 4335E 3-Function Mini Remote Control
(6) Models 747E 727E Keyless Entry System
(7) Model 58LM...............................Multi-Function Door Control Panel
(8) Model 760E ...............................Outside Keylock
(9) Model 1702E .............................Outside Quick Release
(10) Model 770E ...............................The Protector System™
(11) Model 1703E .............................The Chamberlain Arm™
(12) Model FLA230...........................Flashing Light Kit
(13) Model 16200LM ........................Pedestrian Door Switch
(14) Model MDL100LM.....................Mechanical Door Latch Kit
(15) Model EQL01 ............................Door Handle Quick Release
(16) Model 100027 ...........................1-Position Key Switch
(Flush Mount - 100010)
Model 100041 ...........................2-Position Key Switch
(Flush Mount - 100034)
WIRING INSTRUCTIONS FOR ACCESSORIES
Keyless Entry System – To opener terminals: Red-1 and White-2
Outside Keylock – To opener terminals: Red-1 and White-2
Protector System™ – To opener terminals: White-2 and Black-3
Door Control Panel – To opener terminals: Red-1 and White-2
27
114A2074H-GB
SPECIFICATIONS
Max. Pull Force...............800N
Watts ..............................550
Motor
Type................................Permanent split capacitor
Speed .............................1500 rpm
Volts................................230-240 Volts AC-50Hz Only
Drive Mechanism
Gears ..............................16:1 worm gear reduction
Drive ...............................Chain with one-piece trolley on
steel T-rail.
Length of Travel..............Adjustable to 2,3m (7-1/2 feet)
Travel Rate .....................5"-7" (127-178mm) per second
Lamp...............................On when door starts, off 4-1/2 minutes
after stop.
Door Linkage ..................Adjustable door arm. Pull cord trolley
release.
Safety
Personal .........................Push button and automatic reversal in down
direction. Push button and automatic stop in
up direction.
Electronic ........................Independent up and down force
adjustment screws.
Electrical .........................Motor overload protector and low voltage
push button wiring.
Limit Device ....................Circuit actuated by limit nut.
Limit Adjustment .............Screwdriver adjustment on side panel.
Start Circuit .....................Low voltage push button circuit.
Dimensions
Length (Overall) ..............3,1m (122-1/2")
Headroom Required .......5cm (2")
Hanging Weight ..............32 lb (14,5 kg)
Receiver
Memory Registers...........12
Code Switch Memory .....1
Keypad Code Memory ....1
7-GB
A. Door within a door connection
Remove cover. Locate auxiliary terminal block. Remove jumper
from terminal leads 1 and 2 (not shown). Replace with contact
switch leads as shown.
B. Flashing light connection
The flashing light can be installed anywhere. Connect light leads to
terminals 3 and 4 on the terminal block.
C. Coaxial antenna adapter
A coaxial antenna connection can be used if the transmitter range
is too short. Cut off the existing antenna. Use standard coax cable
and connector. Strip off end of insulation to “X” dimension.
433 MHz: X = 250mm 27 MHz: X = 2,44m
Reposition antenna.
SPECIAL FEATURES OF THE 4210E/4410E – 26
MAINTENANCE OF YOUR OPENER
Once a Month:
• Repeat safety reverse test. Make any necessary adjustments.
• Manually operate door. If it is unbalanced or binding, call for
professional garage door service.
• Check to be sure door opens and closes fully. Adjust Limits and/or
Force if necessary.
Once a Year:
Oil door rollers, bearings and hinges. The opener does not require
additional lubrication. Do not grease the door tracks.
REPLACEMENT PARTS – 29
28