Chamberlain 1345M Owner'S Manual Download Page 30

30

Using Your Garage Door Opener

Your Security

®

 opener and hand-held remote control 

have been factory-set to a matching code which changes 
with each use, randomly accessing over 100 billion 
new codes. Your opener will operate with up to eight 
Security

®

 remote controls and one Security

®

 Keyless 

Entry System. If you purchase a new remote, or if you 
wish to deactivate any remote, follow the instructions in 
the 

Programming

 section. 

Activate your opener with any of the following:

•   The Hand-Held Remote Control: 

Hold the push button 

down until the door starts to move.

•   The Wall-Mounted Door Control:

 Hold the push button 

or bar down until the door starts to move.

•   The Keyless Entry (See Accessories):

 If supplied with 

your garage door opener, it must be programmed 
before use. See 

Programming.

When the opener is activated (with the safety reversing 
sensor correctly installed and aligned)

1.   If open, the door will close. If closed, it will open.

2.   If closing, the door will reverse.

3.   If opening, the door will stop.

4.   If the door has been stopped in a partially open 

position, it will close.

5.   If obstructed while closing, the door will reverse. If the 

obstruction interrupts the sensor beam, the opener 
lights will blink for fi ve seconds.

6.   If obstructed while opening, the door will stop.

7.   If fully open, the door will not close when the beam is 

broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door 
won't close from a hand-held remote. However, you can 
close the door with the Door Control, the Outside Keylock, 
or Keyless Entry,

 if you activate them until down travel 

is complete.

 If you release them too soon, the door will 

reverse. 

The opener lights

 will turn on under the following 

conditions: when the opener is initially plugged in; when 
power is restored after interruption; when the opener is 
activated. 

The light will also turn on when someone walks through 
the open garage door. 

It will turn off automatically after 4-1/2 minutes. Bulb size 
is A19. Bulb power is 75 watts maximum.

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING 

WARNING 

WARNING 

WARNING 

1.  READ AND FOLLOW ALL WARNINGS AND 

INSTRUCTIONS.

2.  ALWAYS keep remote controls out of reach of children. 

NEVER permit children to operate or play with garage 
door control push buttons or remote controls.

3.  ONLY activate garage door when it can be seen clearly, 

it is properly adjusted, and there are no obstructions to 
door travel.

4.  ALWAYS keep garage door in sight and away from 

people and objects until completely closed. NO ONE 
SHOULD CROSS THE PATH OF THE MOVING DOOR.

5.  NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY 

OPEN DOOR.

6.  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Use caution 
when using this release with the door open. Weak or 
broken springs or unbalanced door could result in 
an open door falling rapidly and/or unexpectedly and 
increasing the risk of SEVERE INJURY or DEATH.

7.  NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

8.  NEVER use handle to pull garage door open or closed. 

If rope knot becomes untied, you could fall.

  9.  If one control (force or travel limits) is adjusted, the 

other control may also need adjustment.

10.  After ANY adjustments are made, the safety reversal 

system MUST be tested.

11.  Safety reversal system MUST be tested every month. 

Garage door MUST reverse on contact with 1-1/2" 
high (3.8 cm) object (or a 2x4 laid fl at) on the fl oor. 
Failure to adjust the garage door opener properly 
increases the risk of SEVERE INJURY or DEATH.

12.  ALWAYS KEEP GARAGE DOOR PROPERLY 

BALANCED (see page 3). An improperly balanced door 
may NOT reverse when required and could result in 
SEVERE INJURY or DEATH.

13.  ALL repairs to cables, spring assemblies and other 

hardware, ALL of which are under EXTREME tension, 
MUST be made by a trained door systems technician.

14.  ALWAYS disconnect electric power to garage door 

opener BEFORE making ANY repairs or removing 
covers.

15.  

SAVE THESE 

INSTRUCTIONS.

Summary of Contents for 1345M









































Reviews: