background image

Installation Step 11

Fasten Door Bracket 

Follow instructions which apply to your door type
as illustrated below or on page 21.

To prevent damage to steel, aluminum,
fiberglass or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with angle iron.

A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should
cover the height of the top panel. 

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.

• Center the door bracket on the previously marked

vertical guideline used for the header bracket
installation. 

Note the correct UP placement as

stamped inside the bracket.

• Position the bracket on the face of the door within

the following limits: 

A) The top edge of the bracket 2"-4" below the top

edge of the door.

B) The top edge of the bracket directly below any

structural support across the top of the door.

• Mark and drill 5/16" left and right fastening holes.

Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.

If your installation doesn't require vertical reinforce-
ment but does need top and bottom fastening holes
for the door bracket, fasten as shown in Figure 2. 

20

Vertical

Guideline

Door

Bracket

Nut

5/16"-18

Carriage Bolt

5/16"-18x2-1/2"

Lock 

Washer

5/16"

Vertical

Guideline

UP

UP

Door

Bracket

Location

Header

Bracket

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, aluminum, steel,
doors with glass panel, etc).

Vertical

Reinforcement

Door Bracket

Inside Edge

of Door or

Reinforcement Board

SECTIONAL Door Installation Procedure

Carriage Bolt

5/16"-18x2-1/2"

Nut 5/16"-18

Lock Washer 5/16"

Hardware Shown Actual Size

WARNING

Figure 1

Figure 2

Summary of Contents for 1280-298LMC - 1/2 HP





































Reviews: