Opener
Terminal Screws
Antenna
Right Panel
of Opener
Multi-Function
Door Control Panel
Multi-Function
Door Control Panel
Terminal Screws
WHITE
RED
The Chamberlain Group, Inc.
Liftmaster Belt Drive CDO
Install Wall Control
3/5/92 - 3/13/92
LIGHT
LOCK
Door Control
Button
Light Button
Lock Button
KG
KG
M.D.C. CERT. NO.
1
3
9
7
5
132C2105-1
WARNING: To reduce the risk of severe injury
or death by entrapment, when adjusting either
the force or limits of travel controls ensure that
the door reverses on a 1 inch object (or a 2 x 4
board laid flat). See instructions for proper
adjustment procedure.
This device complies
with FCC Rules Part
15. Operation of this
device is subject to the
following conditions:
1. This device may
not cause harmful
interference. 2. This
device must accept
any interference
that may be received,
including interference
that may cause
undesired operation.
PART NO:
Nº DE PIÈCE:
D.O.C. CERT. NO.
DATE:
PAT. #RE29,525; 4,750,201; 4,806,930 Other Patents Pending.
AVERTISSEMENT: Pour réduire les risques de
blessures mortelles par happement, après tout
réglage de la force de déclenchement ou des
seuils de fin de course s'assurer que le sens de
la course s'inverse lorsque la porte entre en
contact avec un object de 13 mm (1 po) de
hauteur (ou un madrier de 2 x 4 de section, à
plat) posé sur le sol. Effectuer les reglages
selon les procédures décrites dans la notice.
1
3
9
7
5
2
3
TO PROGRAM RECEIVER CODE
FOR EACH REMOTE CONTROL
1. Press and HOLD remote control
transmitter push button.
2. Press receiver code button. The opener
light will flash once.
3. Release transmnitter button. Opener
has learned code.
TO ERASE ALL RECEIVER CODES
1. Press and HOLD receiver code button.
Green indicator light alongside will turn
ON.
2. When light turns OFF (about 6
seconds) ALL codes are erased from
opener memory.
1
2
1
Installation Step 6
Install the Multi-Function
Door Control Panel
14
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death. Install the door control
(or any additional push buttons) out of the
reach of children and away from all moving
parts of the door and door hardware,
but
where the garage door is visible. Do not allow
children to operate the push button(s) or the
remote control transmitter(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
• Strip 1/4" of insulation from one end of the bell
wire; connect the wire to the two screw terminals
on the back of the door control by color: white to 2
and white/red to 1.
• Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Multi-Function Door Control securely
with 6ABx1" screws. If installing into drywall, drill
5/32" holes and use the anchors provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, creating a short.
• Receiver terminal screws and the antenna are
located on the right panel of the opener. Position
the antenna wire as shown.
• Then connect the bell wire to the opener terminal
screws: white to 2 and white/red to 1.
• Remember to affix the User Safety Instruction
label to the wall near the door control, and the
Maintenance Instruction label in a prominent
location on the inside of the garage door.
If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time) use tacks
to secure the label alongside the door control.
Page 28 explains how to operate the opener using
the lighted push button and the Lock & Light
features available on the Multi-Function Door
Control Panel.
Dry Wall Anchors
Insulated
Staples
6AB x 1" Screw
Multi-Function Door Control
Hardware Shown Actual Size
Outside Keylock Accessory Connections
To opener terminal screws: white to 2; white/red to 1
WARNING
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full
open position but will not return to the
close position until the sensor beam is
connected and properly aligned.
See Safety Reversing Sensor Instructions
beginning on page 17.
