Model OE-9
Installation, Operation and Maintenance
Page 8
Rev. 02/1208
A1151_MAGNUM.doc
Thread opposite end of hose into male #6
fitting (
factory installed
) attached to power
column as shown in
Fig 10
.
27) From Idler Column route the hydraulic hose
(
factory installed from cylinder to top of column
)
up to Overhead.
L
OOSEN FACTORY INSTALLED
CLAMP AT TOP OF
I
DLER
C
OLUMN AND GENTLY PULL UP
ANY SLACK FROM HOSE
. Install a hose clamp in
column extension and in overhead beam with
(1) 3/8”-16 x 3/4" lg. hex flange bolt and hex
flange nut per clamp as shown in
Fig 11a.
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP WITH
3/8"-16 HEX FLANGE BOLT & NUT
HYDRAULIC HOSE CLAMP WITH
3/8"-16 HEX FLANGE BOLT & NUT
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP WITH
3/8"-16 HEX FLANGE BOLT & NUT
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP WITH
3/8"-16 HEX FLANGE BOLT & NUT
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
Fig 11a – Hydraulic Hose from Idler Column to
Overhead.
(Sync cables removed for clarity)
28)
Route hydraulic hose from Idler column
across Overhead to the Power Column and
down inside of Power Column (routing is
identical to Idler Column) to male #6 JIC
bulkhead “T” fitting. Loosely attach hose to
“T”.
If this is an extended height lift (model
CL9-1 or CL9-2), an extension hose
(supplied)
will connect the Idler hose to the “T” fitting.
29) While gently pulling slack up from the “T”
fitting to the top of the power column
extension,
twist the hose until it lays flat in
the overhead beam
.
(When installing lift at
narrow or low setting, excess hose should be
snaked in bottom of overhead, Fig 11a.
When installing at narrow and low setting,
form a loop in the column extension between
the overhead support plate and the inside
wall of the column extension, Fig 11b.)
Install hose clamps identical to idler side, one
hose clamp at the top of the column, one at
the top of the column extension and one at
the end of the overhead.
Fig 11b
. Tighten
connection at “T” fitting.
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP
WITH 3/8"-16 HEX FLANGE
BOLT & NUT
LOOP EXCESS HOSE
IN COLUMN EXT. WHEN
INSTALLING AT NARROW
AND LOWERED SETTING
LOOP EXCESS HOSE
IN COLUMN EXT. WHEN
INSTALLING AT NARROW
AND LOWERED SETTING
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP
WITH 3/8"-16 HEX FLANGE
BOLT & NUT
LOOP EXCESS HOSE
IN COLUMN EXT. WHEN
INSTALLING AT NARROW
AND LOWERED SETTING
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP
WITH 3/8"-16 HEX FLANGE
BOLT & NUT
LOOP EXCESS HOSE
IN COLUMN EXT. WHEN
INSTALLING AT NARROW
AND LOWERED SETTING
SNAKE EXCESS HOSE
IN OVERHEAD WHEN
INSTALLING AT NARROW
OR LOWERED SETTING
HYDRAULIC HOSE CLAMP
WITH 3/8"-16 HEX FLANGE
BOLT & NUT
Fig 11b –
Hydraulic Hose from Overhead to
Power Column.
(Sync cables removed for clarity)
30)
B
E
C
ERTAIN
A
LL
F
ITTINGS AND
C
ONNECTIONS
ARE
T
IGHT
.
I
T IS THE INSTALLERS
RESPONSIBILITY TO INSURE SYSTEM IS LEAK
-
FREE
.
Fill the Power Unit with three gallons of
clean 10wt anti-foam anti-rust hydraulic oil or
Dexron
III
ATF.
D
O
N
OT
U
SE
O
ILS
W
ITH
D
ETERGENTS
.
F
OR LIFTS WITH OPTIONAL
DUAL PENDANT
CONTROL,
SKIP STEPS
26
THRU
31
AND
REFER INSTEAD TO THE
“D
UAL
P
ENDANT
C
ONTROL
I
NSTALLATION
& O
PERATION
M
ANUAL
S
UPPLEMENT
”.
L
OCK
R
ELEASE
31)
Attach Mechanical Lock Release Cable
Assembly to Power Column Lock Release
Clevis using the 3/16” diameter x 1/2" long
pin and (2) “C” clip retainers,
Fig 12
.
32)
Insert threaded sleeve portion of cable
assembly in slot located on tab above locking
pawl,
Fig 12
. One jam nut should be located
on each side of tab. Position threaded sleeve
with ½” of thread below tab as indicated in
Fig 12
and tighten jam nuts.
