Challenger Lifts Magnum Versymmetric OE-9 Installation, Operation & Maintenance Manual Download Page 17

Page: 17 / 20

Model OE-9

Installation, Operation and Maintenance

Page 17

Rev. 02/1208

A1151_MAGNUM.doc

PARTS BREAKDOWN

(continued)

Fig D. Synchronizer

ITEM #

PART # QTY/LIFT DESCRIPTION

A1115-0

SYNCHRONIZER CABLE – OE-9 (32’-8”) [ Cable Pack #A1003-0 ]

A1115-1

SYNCHRONIZER CABLE – OE-9-1 (34’-8”) [ Cable Pack #A1003-1 ]

A1115-2

SYNCHRONIZER CABLE – OE-9-2 (36’-8”) [ Cable Pack #A1003-2 ]

A1116

½-20NF HEX NUT

A1117

½-20NF HEX JAM NUT

A1041

SHEAVE ASSEMBLY (3 ½” DIA. X ¼” GROOVE)

A1062

SHEAVE PIN

A1063-S

SHORT SHEAVE SPACER

A1063-L

LONG SHEAVE SPACER

36013

1" I.D. SPACER WASHER

36014

1" EXT. RETAINING RING

A1158

CL9 LOWER CABLE TRAP

Replace all worn or broken parts with genuine

Challenger Lifts Inc.

parts.

Contact your local Challenger Lifts Parts Distributor for pricing and availability.

(Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area)

Summary of Contents for Magnum Versymmetric OE-9





















Search results

Summary of Contents for Magnum Versymmetric OE-9

Reviews:

Related manuals for Magnum Versymmetric OE-9

Brands by name

Popular brands

Challenger Lifts Magnum Versymmetric OE-9, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for Magnum Versymmetric OE-9

Reviews:

Related manuals for Magnum Versymmetric OE-9

Brands by name

Popular brands