background image

terminals together may cause burns or a fire.

5. Under abusive conditions, liquid may be ejected from the battery, avoid 

contact. If contact accidentally occurs, flush with water. If liquid contacts 
eyes, additionally seek medical help. Liquid ejected from the battery may 
cause irritation or burns. 

Additional Warnings Applicable for the Cordless Drill

Hold power tool by insulated gripping surfaces, when performing an 
operation where the cutting accessory or fastener may contact hidden 
wiring.

 Cutting accessory and fasteners contacting a “live” wire may make

exposed metal parts of the power tool “live”, which can give the operator 
an electric shock.

Use appropriate detectors to determine if utility lines are hidden in the 
work area or call the local utility company for assistance.

 Contact with 

electric lines can lead to fire and electric shock. Damaging a gas line can 
lead to explosion. Penetrating a water line causes property damage and 
may cause an electric shock.

Switch off the power tool immediately when the tool insert jams.

 Be 

prepared for high reaction torque that can cause kickback.

Hold the machine with a firm grip. 

High reaction torque can briefly occur 

while driving in and loosening screws.

Secure the work piece.

 A work piece clamped with clamping devices or in

a vice is held more securely than by hand.

Be extra careful when cutting in high or hard-to-reach locations.

 

Avoid 

sawing overhead.

 Be on the lookout for hidden wires and falling debris.

Keep your workplace clean. 

Blends of materials are particularly 

dangerous. Dust from light alloys can burn or explode.

Always wait until the machine has come to a complete stop before 
placing it down. 

The tool insert can jam and lead to loss of control over 

the power tool.

Do not open the battery.

 Danger of short circuiting. Protect the battery 

against heat, e. g., also against continuous sun irradiation and fire. There is
danger of explosion.

In case of damage and improper use of the battery, vapours may be 
emitted.

 Provide fresh air and seek medical help in case of complaints. 

The vapours can irritate the respiratory system.

When the battery is defective, liquid can escape and come into contact 
with adjacent components.

 Check any parts concerned. Clean such parts 

or replace them, if required.

Important Safety Instructions for Battery Charger

Before using battery charger, read all instructions and cautionary 
markings on battery charger, battery pack, and product using battery.

Use only the charger which accompanied your product or direct 
replacement.

 Do not substitute any other charger. Use only same supplier 

approved chargers with your product.

Do not disassemble charger or operate the charger if it has received a 
sharp blow, been dropped or otherwise damaged in any way.

 Incorrect 

4

Summary of Contents for VDRILXACT













Reviews: