background image

 

Avoid Skin and Eye Contact 

Mineral oil products degrease your skin. If your skin comes in contact with these 

substances repeatedly and tor an extended period, it will desiccate, various skin 

diseases may result. Also, allergic reactions are known to occur. Eyes can be 

irritated by contact with oil. If oil comes into your eyes, wash them with clear 

water, if your eyes are still irritated, see a doctor immediately! 

 

Refuelling 

 

 

 

 

Important! 

1.

 

Follow the safety precautions! 

2.

 

Be careful and cautious when handling fuels. 

3.

 

The engine must be turned off and cooled down. 

4.

 

Carefully clean the area around the fuel tank filler neck to keep dirt from getting in 

the tank. 

5.

 

Place the Certa Petrol Demolition Concrete Saw on an even surface. 

6.

 

Unscrew the tank cap and fill tank with fuel mixture. Take care to avoid spilling. 

7.

 

Screw the tank cap back on hand-tight 

8.

 

Clean screw cap and tank after refuelling. Never start or operate the Certa Petrol 

Demolition Concrete Saw in the same place as it was fuelled! 

9.

 

If fuel gets on your clothing, change clothes immediately. 

Fuel Mixture 

Summary of Contents for CTPTDCSAWA









































Reviews: