manualshive.com logo in svg

Certa CTPTDCSAWA, User Manual, Page: 18 / 40

Share
Download
Certa CTPTDCSAWA User Manual Download Page 18

Place the Certa Petrol Demolition Concrete Saw on a stable surface and carry out the 

following assembly steps: 

Mounting the cutting disc 

 

 

 

1.

 

Cross sleeve 

2.

 

Allen key 

3.

 

Cutting disc 

4.

 

Large plate #1 

5.

 

Small plate 

6.

 

M10x20 Hexagon screw 

7.

 

Large plate #2 

8.

 

Belt protection cover 

 
The inner hole of the cutting disc is selected to be installed in sequence as shown in the 

second configuration image above: 

•

 

Large plate #1, cutting plate (the cutting direction is consistent with the arrow of 

the wheel housing), Large plate #2 (with the small step facing outward), small 

plate, then the M10x20 outer hexagonal screw. 

 
The inner hole of the cutting disc is 25.4, which shall be installed in sequence as shown in 

the first configuration image above:  

•

 

Large plate #2 (small step outward), cutting plate (the cutting direction is 

consistent with the arrow of the grinding wheel cover), large plate #1, small plate, 

then the M10x20 outer hexagonal screw shall be installed. 

 

 

 

Summary of Contents for CTPTDCSAWA









































Reviews:

No comments