CENTURY PRODUCTS Ninja Pro Instruction Manual Download Page 23

Page: 23 / 28

Collective and Throttle:
Slowly raise the throttle stick to HIGH,
Helicopter should be lifts off at haft stick open,
When helicopter is just about to take off, it inclines
to some directions. Correct the inclination by using
your radio trim.

Rudder:
When the helicopter is just about to take off,
make a correction trim first then use rudder stick
to control Left & Right, Note! Now is good time
to give your gyro a final adjustment. (see your
GYRO manual.)

Elevator:
When the helicopter is just about to take off,
make a correction trim first then use elevator stick
to control Forward & Backward.

Roll(Aileron):
When the helicopter is just about to take off,
make a correction trim first then use Aileron stick
to control slide to Left or slide to the Right..

Ninja Pro 30-46 Helicopter Kit Replacement Parts List
2002-000

Ninja Metric Hardware Pack .................... 1 19.95 D

2002-007

Main Blade Grip ....................................... 1 28.95 D

2002-007A Spacer ....................................................... 2 3.00 D
2002-008

Blade Grip Bearing 5x13x4 ...................... 2 11.95 D

2002-009

Pitch Arm .................................................. 2 14.95 D

2002-010

Main Blade Grip Assembly ...................... 1 88.95 D

2002-011

Damper Rubber ......................................... 4 5.95 D

2002-013

Flybar Control Arm ................................... 1 8.95 D

2002-015

Spring Steel Flybar ................................... 1 4.95 D

2002-017

Seesaw ...................................................... 1 16.50 D

2002-019

Seesaw Arm .............................................. 2 16.50 D

2002-020

Seesaw Ball Bearing 3x7x3F (OP) ........... 1 14.50 D

2002-021

Washout Base Unit .................................... 1 26.50 D

2002-022

Ball Bearing 3x6x2.5F (OP) ..................... 4 29.95 D

2002-022A Ball Bearing 3x6x2.5 (Master) ................ 4 17.95 D
2002-023

Washout Arm ............................................ 2 18.50 D

2002-024

Washout Assembly (W/Pl Bearing) .......... 1 49.95 D

2002-025

Radius Link ............................................... 2 4.95 D

2002-027

Linkage Set W/Ball End(1) ...................... 1 16.50 D

2002-026

Washout & Mixing Arm B.B. ................... 4 17.95 D
-3x6x2.5 (Master)

MOD 1 MOD 2

LEFT

RIGHT

DOWN

(B)

(F)

(B)

RIGHT

LEFT

RIGHT

N i n j a P r o & P r o M a s t e r P a r t s L i s t

2 3

2002-029

Flybar Paddle ............................................ 2 14.95 D

2002-031

Swashplate assembly ................................ 1 64.95 D

2002-032

Swashplate Antirotation-Screw ................ 1 3.95 D

2002-039

Mixing Arm B.B. Pack 3x6x2.5F(OP) ..... 14 79.95 D

2002-043

Main Rotor Blade (prebuilt) ..................... 2 42.95 D

2002-049

Canopy Mount (A & B) ............................ 3 7.95 D

2002-051

Servo Adapter Rear (A & B) .................... 2 4.95 D

2002-055

Rx & Gyro Tray Mount ............................ 4 6.50 D

2002-057

Starter Belt Retaining Clip ........................ 2 2.50 D

2002-059

Collective Plastic Busing .......................... 2 1.50 D

2002-061

Collective B.B. 6x10x3F (OP) ................. 2 12.95 D

2002-063

Fuel Tank- 10 OZ ...................................... 1 4.50 D

2002-065

Canopy (Without Mount) .......................... 1 22.95 D

2002-066

Landing Skid Only .................................... 2 15.95 D

2002-067

Tuf Landing Gear Set ............................... 1 29.95 D

2002-068

Landing Strut Only ................................... 2 15.95 D

2002-069

Elevator Lever .......................................... 1 19.50 D

2002-070

Elevator B.B. 4x8x3F (OP) ...................... 2 12.95 D

2002-071

Collective Pitch Lever Set ........................ 1 12.95 D

2002-072

Elevator Plastic Bushing ........................... 2 1.50 D

2002-073

Rudder Mount Plate .................................. 1 12.95 D

2002-075

Push Pull Collective “Y” Lever ................ 1 5.50 D

Summary of Contents for Ninja Pro





























Search results

Summary of Contents for Ninja Pro

Reviews:

Related manuals for Ninja Pro

Brands by name

Popular brands

CENTURY PRODUCTS Ninja Pro, Instruction Manual

Search results

Summary of Contents for Ninja Pro

Reviews:

Related manuals for Ninja Pro

Brands by name

Popular brands